This site is now in read-only archive mode. Please move all discussion, and create a new account at the new Victron Community site.
Hello All,
I have been digging through my Cerbo GX settings trying to find a way to display data from both of my PV controllers on the main screen. I found this image online that shows exactly what I'm trying to do.... Any idea how to get this additional data to appear on the display as shown below?
I'm pretty sure this is a modified UI. Take a look into the modification space.
I think this question is better suited in the Modification space.
So I move it there.
BR
The image is someone's use of my "GuiMods". It provides this and other functionality such as tank and temperature info along the bottom of the screen, power gauges for AC in/out, inverter, battery. A power gauge for the PV Charger was also just added.
If you add names to your PV chargers, those names will appear where -- are in the image above.
https://github.com/kwindrem/GuiMods
You will also need SetupHelper for the install
https://github.com/kwindrem/SetupHelper
Thanks Kevin, that adds exactly the functionality I was looking for... Problem is, I'm no programmer and looking at your instructions gives me a headache, I have no clue what to do. Any possibility of me hiring your expertise to make the code changes for me?
I can certainly help you get this going. There is no code to write, just installing the package and running a setup script.
If the Cerbo is connected to the internet, then the easiest thing to do is enable superuser and SSH login and run a couple of commands:
wget -qO - https://github.com/kwindrem/GuiMods/archive/current.tar.gz | tar -xzf - -C /data mv /data/GuiMods-current /data/GuiMods wget -qO - https://github.com/kwindrem/SetupHelper/archive/current.tar.gz | tar -xzf - -C /data mv /data/SetupHelper-current /data/SetupHelper /data/GuiMods/setup
Select install at the first prompt, then proceed to answer all the questions.
There are ways I can simplify the installation process for you but would need to collect information about your system.
My package will reinstall itself if possible but future versions of Venus OS may require repeating the installation steps.
Pardon my ignorance but all I need to do is enable superuser and SSH then type in that list of commands you posted? The Cerbo is connected to the Internet full time via cellular / WIFI on my boat.
Yes. And use copy/paste on the commands to make your life easier. You can copy the entire set of instructions and paste them all at once. Good luck and check back if you have problems. I'm here to help.
Instructions for root access and ssh are here:
https://www.victronenergy.com/live/ccgx:root_access
Look into the part about ssh keys. It makes things so much easier and survives a Venus OS update.
Were you able to get this going?
Let me know if you need more help.
No... I haven't figured out how to enable super suer and SSH, is that done physically on the Cerbo or through the VRM panel? The system is online so hopefully I can do this remotely once I figure out how to do it. Are you able to email me at cdpurchas@gmail.com?
Very sorry you are having problems.
The white screen indicates ONE of the screens can’t be drawn. You should be able to swipe sideways to get to the other overview pages, then you can touch the menu button to get to those screens.
The “cat: can’t open …” might be a clue. I haven’t tested installation without the power gauges since I added that code.
Try answering no to the flow overview enhancements and see if the white screen is gone. If so, then that’s the screen with issues.
Next, try answsering yes to the flow overview then answering yes to the power gauges option and enter any set of power values, eg, 1400 2000 300 3600 then 200 for the battery charging limit. If that results in curing the white screen, then go back and run setup install again and try answering no to the power gauge question.
If the flow overview isn’t the problem screen, you can try not installing the mobile overview enhancements.
Also, let me know which Venus version you are running. I know there are issues with 2.70~16 and beyond but can’t remember if I got a white screen.
The log for the GUI is /var/log/gui/current:
tail -100 /var/log/gui/current | tai64nlocal
Any errors should appear at then end of the log after switching to the problem page.
Firmware version is 2.66, is that what you mean? Got that from Settings/Firmware.
I need more information before I can help further. I need to know what modification is causing the problem and need to know what the error is from the log.
Run setup and select uninstall.
Reboot
Run setup and select install.
Enable all options.
Swipe through all pages. If there’s a white screen, email me the log at
/var/log/gui/current.
email: kwindrem@icloud.com
Tried it again, accepting all the options, got a white screen, couldn't swipe, Cerbo appears frozen. Ran the command to get logs, said "permission denied" see below:
-sh: /var/log/gui/current: Permission denied
root@einstein:~#
Hello Kevin. is it necessary to install the setup helper? or do I just have to proceed like the installation description in the readme file? Superuser is running on my device.
Yes, you need SetupHelper for any of my packages and for the other packages starting to use it like the 123electric SmartBMS.
I just checked and the GuiMods ReadMe is out of date. The ReadMe also includes manual download/install instructions, but these include installing SetupHelper as well. At one point, SetupHelper and GuiMods were installed via the blind install mechanism. I eliminated GuiMods from the blind install since you get the same functionality by adding the GuiMods .tar.gz file to the same media.
The install instructions in SetupHelper detail how to install other packages on the same USB stick/SD card as used for the SetupHelper blind install.
There are two parts to SetupHelper:First, it provides functions that all of my package setup scripts use. These functions simply the setup scripts.
Second is automatic updates from GitHub or from USB/SD media, and reinstall after a Venus update. V4.0 switched this functionality to PackageManager which is part of SetupHelper.
You can technically disable PackageManager if you only want command line based install/uninstall. But you would need to edit the SetupHelper setup script to do so.
You can disable the functionality PackageManager provides by setting automatic download and automatic install off. You'd also want to avoid inserting an SD card with any package .tar.gz files on it into the GX device.
The command line based install/unstill still works although it is not documented in the ReadMe documents. Just run the setup script one the package is manually placed in /data, e.g.,
/data/SetupHelper/setup /data/GuiMods/setup
Thank you very much Kevin. Is there also the possibility to restore the system after a flash error or blue screen? Unfortunately I'm not a computer genius and I'm a bit scared ;)
As far as SetupHelper and my other packages are concerned, the blind install procedure can be repeated if problems occur there, but again this is not likely.
sorry, your Downloadlink dont work
https://github.com/kwindrem/GuiMods/raw/main/venus-data.tgz
@Kevin Windrem Can you go follow this link there is a bug that has been found thank you https://community.victronenergy.com/questions/114259/venus-os-large-features-menu-missing-on-28033large.html?childToView=114415#answer-114415
Thank you for your work Kevin. since the past weekend the gui mod is running perfectly
