question

David avatar image
David asked

Multiplus II 48v 3000 or 5000 max charge voltage?

I'm looking at using a Multiplus II 48/3000 or 48/5000 with a bank of Nissan Leaf cells.

I was hoping to run in 16S - which would get me to a final voltage of 4.12v per cell so 65.96v total. I notice this is just under the Max DC input limit of 66v.

However, I'm not sure what the charger can charge to? Can it go this high or will I need to drop to 14S


Multiplus-II
3 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Rob Duthie avatar image Rob Duthie commented ·

Hi Slimf

I would run with 14S as this works perfectly ,as i run and use the 14S Nissan leaf cells with a BMS attached as well. As 14S is the perfect voltage to use with the Victron Mulitplus2, as this is what i have. Much easy to integrate than the Telsa cells.

And to date no issues recorded it just works well.


Regards

Rob D

New Zealand

1 Like 1 ·
David avatar image David Rob Duthie commented ·

Thanks - This was the answer I was after. Damn, I have 32 modules, so am going to need to find another three so I can do 5P. Got any over there you want to ship to NSW Australia?! My modules are testing at around 350wh - so bit of degradation since new in 2011.

0 Likes 0 ·
Show more comments
4 Answers
Tom avatar image
Tom answered ·

Have a look here https://youtu.be/K47NLwHyZng

This set up uses the Leaf battery and a 48/5000 Quatro.

1 comment
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

David avatar image David commented ·

Thanks - I have seen that before.. I can see they are recommending 14S as well. I suppose that answers my question hey :-)

0 Likes 0 ·
sean avatar image
sean answered ·

I have approximately 140kWh of Leaf cells attached to a number of MPII in parallel - 16s - Batrium etc ....

Max charge voltage of the MPPTs, and the MPII is 64v - which equates to 4v/cell.

4.12v/cell will lessen cell longevity.

65.96v is rather to close to the MPII max voltage.



2 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

raff-celis avatar image raff-celis commented ·
Hey Sean! Looks cool, Can I ask what BMS are you using and where you get it?
0 Likes 0 ·
sean avatar image sean raff-celis commented ·
Batrium
0 Likes 0 ·
larsea-dk avatar image
larsea-dk answered ·

Hi Rob

Im struggling finding out how to set my settings in the multiplus 2 for my 14s nissan cell setup. Would you share your settings?? I have set my jk bms to control my mppts. At the moment they are set to charge to 57.4volt which is 4.1v(pack is not yet equal and is between 4.08-4.13 when voltage is 57.4v)

Im from Denmark so of course need to set grid to Denmark.

Thank you very much in advance

2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Rob Duthie avatar image
Rob Duthie answered ·

Hi

As per attached system settings.

New Text Document.txt


1 comment
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

larsea-dk avatar image larsea-dk commented ·
Great, thanks. I'll take a look to check I understand it :-)
0 Likes 0 ·