MPPT 100/50 Sometimes won't start charging in the morning

Question

replit

This site is now in read-only archive mode. Please move all discussion, and create a new account at the new Victron Community site.

question

david-p asked May 7, '24

MPPT 100/50 Sometimes won't start charging in the morning

Hi,

I have two PV Strings - 1 connected to a SmartSolar 100/20 and the other (larger) string connected to a SmartSolar 100/50. Whilst the 100/20 works perfectly well, the 100/50 controller occasionally does not restart charging in the morning. This may happen once every 5 to 10 days. I can get it going again by turning charging off then on and all will work fine until next time. If it does not start and I leave it not charging, then it may start charging again the following morning! There doesn't appear to be any consistency as to when it might not start charging.

I reckon this started happening after a firmware upgrade about 3 or 4 updates ago. Each time I try to update to a newly released version I hope that it will fix the issue - but unfortunately not. It used to work perfectly fine for over a year. Both units are configured with exactly the same settings.

Is anybody else getting the same issues? Any suggestions?

Thanks!

David

smart solar charging behaviour

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Daniël Boekel (Victron Energy Staff) ♦♦ commented · Jun 18 at 01:37 PM

Hi @david-p

i've tried to email you but it bounced, is there an address where I can reach you?

you can set your reply to be only visible to admins to not expose your email address

0 ·

Modifications Space

Node Red Space

Answer 1 · 2024-05-07T04:45:27Z

klim8skeptic answered · May 07 at 04:45 AM

@david-p it sounds like your PV voltage might not be high enough tfor the mppt to start charging the battery.

Post a screenshot of the mppt's detailed history, and charge settings.

Specs of your solar panels would be useful.

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 2 · 2024-05-07T06:37:11Z

david-p answered · May 07 at 06:37 AM

Thanks for the quick response. Here is a screenshot of when I was on holidays and didn't restart the charging. As you can see there is plenty of PV voltage. The unit started charging by itself the next day.

Here are the charge settings:

Also please note that if the unit is not charging, I flick the 'Charge Enabled' button off then on and it immediately starts charging so I suggest it would not be a low PV issue.

For the panels in this string, there are 6 x 150w in a 3 parallel lots of 2 panels connected in series (if that makes sense!) They are fairly old panels.

Let me know if you require more info.

Cheers,

David

1715063196502.png (142.2 KiB)

1715063384351.png (92.2 KiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 3 · 2024-05-07T09:30:55Z

Guy Stewart (Victron Community Manager) answered · May 07 at 09:30 AM

Hi @david-p,

Apologies for the issue and thanks for the detailed report, I've asked R&D to have a look at your post.

We recently release firmware v1.64 to address a similar issue with the smaller models - https://professional.victronenergy.com/news/detail/244/

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

david-p commented · May 07 at 12:16 PM

Great, thanks @Guy Stewart (Victron Community Manager) . Looking at the fix for the 100/20, it certainly looks like it may fix the issue with the 100/50. I look forward to trying the fix when it comes through.

Cheers,

David

0 ·

Answer 4 · 2024-06-12T22:29:35Z

benoit-lamy answered · Jun 12 at 10:29 PM

I have the same issue. I have 2 string of 3 x 190 watts panel each connected in series. 1 string is connected to a 100/30 no issues, and 1 string connected to a 100/50. I have no issues with the 100/30, but the 100/50 sometime not always goes into Wakeup mode and will not charge until I turn charging Off and then On. Hope the next firmware update fixes this issue.

Ben

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) ♦♦ commented · Jun 13 at 09:23 AM

Hi @Benoit Lamy

Which firmware version are you running now?

0 ·

benoit-lamy Guy Stewart (Victron Community Manager) ♦♦ commented · Jun 13 at 10:10 AM

Both MPPT are running V1.64.

0 ·

Answer 5 · 2024-06-15T02:13:28Z

david-p answered · Jun 15 at 02:13 AM

Hi @Guy Stewart (Victron Community Manager) ,

I upgraded the firmware yesterday to 1.64 on both the 100/20 and 100/50 units with fingers crossed. The 100/20 woke up this morning fine with no issues but unfortunately, the 100/50 failed to start charging. Once I disabled / enabled charging, it started to work fine. It was a bit foggy this morning so not a lot of sun. I left it for a few hours but still no go until I restarted. FYI The V max on the History screen shows 83.39V and the Voltage just before I restarted was 77.34V.

Please let me know if you require any further info.

Regards,

David

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 6 · 2024-06-18T00:25:25Z

benoit-lamy answered · Jun 18 at 12:25 AM

This morning my 100/50 MPPT was in Wakeup mode again. I had to turn charging off and back on. Started working again.

Ben

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 7 · 2024-06-18T00:47:26Z

neptuneuk answered · Jun 18 at 12:47 AM

HI @Benoit Lamy and @david-p

Strange question but what is the morning temperature of where your MPPT are installed? Like within 12 inches of them?

Then check to your low temperature cutoff setting and see if it's enabled.

If enabled turn it off and see what happens or set higher low temp cutoff for testing.

Probably not this given time of year, but......................

4

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

benoit-lamy commented · Jun 18 at 12:55 AM

I live in Ottawa Canada and the temp this morning was 15 degree Celsius.

0 ·

neptuneuk benoit-lamy commented · Jun 18 at 03:51 PM

OK, rules out the low temp cutoff, unless it's set higher than that!

I have 3 x 100/50 all running FW 1.64.

Currently I am not experiencing any issues.

1.) Did you try enabling and disabling the low temperature cutoff in the Victron Connect app?

2.) Was the temp measured at the MPPT?

3.) What time was the temperature recorded?

0 ·

Show more comments

Answer 8 · 2024-06-24T06:29:24Z

david-p answered · Jun 24 at 06:29 AM

Hi @Guy Stewart (Victron Community Manager) ,

Any update on this issue? It appears @Benoit Lamy has the same issue and we are on opposite sides of the planet (and seasons)!

Cheers,

David

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) ♦♦ commented · Jun 24 at 07:57 AM

I've forwarded it on to R&D, They tried to get in touch via the email you used registering for the community but it bounced?

I have also forwarded on @Benoit Lamy's contact.

0 ·

david-p Guy Stewart (Victron Community Manager) ♦♦ commented · Jun 24 at 11:52 PM

Apologies for that @Guy,

I have fixed the email issue. Please get R&D to resend.

Cheers,

David

0 ·

Answer 9 · 2024-07-04T13:10:46Z

benoit-lamy answered · Jul 04 at 01:10 PM

Today My 100/50 did not come out of Wakeup mode. Temp in Ottawa Canada 09:00 is 21 Celsius.

I have noticed something my MPPT 100/30 as 4 entry in the VE Smart networking, Using battery voltage sense from Shunt, Using External battery current sense from shunt, using external battery temp from SmartBatterySense and Synchronized charging.

On my MPPT 100/50 I am missing Using external Battery current sense from Shunt.

If this helps

Ben

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

david-p commented · Jul 19 at 11:09 PM

@Benoit Lamy - I just posted an update below before reading your message. It appears we're experiencing the same issues and thinking along similar lines!

0 ·

Answer 10 · 2024-07-19T06:51:15Z

david-p answered · Jul 19 at 06:51 AM

I have interesting update - I think it might relate to the networking side of things. If, on the 100/50, I leave the network and then rejoin, the charging starts again. I have previously tried deleting the network on all devices and creating again but the problem still exists.

I notice on the 100/20 it says it is using battery current sense from the Smartshunt but the 100/50 does not show this. Here are some screenshots:

Not sure if that is causing issues.

@Guy Stewart (Victron Community Manager) - any thoughts?

Thanks,

David

img-0920.jpeg (649.7 KiB)

img-0919.png (351.4 KiB)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) ♦♦ commented · Jul 22 at 04:05 AM

Hi @david-p,

Thanks for the updated report. We will have more info this week.

0 ·

Answer 11 · 2024-07-29T07:54:29Z

xtznig answered · Jul 29 at 07:54 AM

Hi,

Are there any News on this topic?

I have the Same Problem.

Best regards

Dominik

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 12 · 2024-08-16T19:32:57Z

benoit-lamy answered · Aug 16 at 07:32 PM

Update. I have purchased a new MPPT 100/50 to replace my 100/30. I now have 3 MPPT 2 x 100/50 and 1 x 100/30. this morning I had MPPT 1 in the OFF mode but not my second 100/50 or my 100/30. So I now suspect that one of my 100/50 is defective.

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 13 · 2024-08-17T09:59:51Z

david-p answered · Aug 17 at 09:59 AM

@Guy Stewart (Victron Community Manager), any news on this? It’s still happening in my setup. I don’t see how it could be a hardware issue if the charging can be restarted simply by either toggling charging or removing from the VE network. Cheers, David

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) ♦♦ commented · Aug 21 at 04:12 AM

Hi @david-p,

Thanks for following this up, I have just asked for an update.

0 ·

david-p Guy Stewart (Victron Community Manager) ♦♦ commented · Sep 02 at 10:27 PM

Hey Guy, Any news? Thanks, David

0 ·

question

MPPT 100/50 Sometimes won't start charging in the morning

Related Resources

question details

Modifications Space

Node Red Space

question

MPPT 100/50 Sometimes won't start charging in the morning

Related Resources

question details

Related Questions

Modifications Space

Node Red Space