Change MPPT Tracking Refresh Interval

Question

replit

This site is now in read-only archive mode. Please move all discussion, and create a new account at the new Victron Community site.

question

Matt Knight asked Mar 5, '19

Change MPPT Tracking Refresh Interval

We collect data from our Victron system and store it for analysis. Here you can see the power generation curve from our rooftop solar panels, connected to a Victron 100/50 solar charge controller.

As you can see, every 10 minutes, the power drops off dramatically. I'm guessing this is the solar charge controller sweeping to find the Maximum Power Point.

Each of these "sweeps" takes ~33 seconds to complete, and during this time, power production decreases dramatically - the middle drop on the chart above is ~158W to ~120W average or so (about a 25% decrease). Power production after the sweep appears almost completely unchanged - looking at the PV input voltage, it reduced by ~0.18V (from 34.50V to 34.32V).

Treating this as a duty cycle and averaging over time, a 25% drop for 33 seconds every 10 minutes corresponds to roughly a 1.4% total drop in output.

Questions:

Am I understanding the purpose of these drops correctly?
Would the MPPT adjustment provide >1.4% improvement to output during the next 10 minutes?
Is it possible / does it make sense to make the interval between these event adjustable - i.e. a user setting to change it?

Thanks,

Matt

MPPT Controllers Solar Panel

screen-shot-2019-03-05-at-100426-am.png (137.7 KiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) answered · Mar 18, 2019 at 01:04 PM

1. I can't say for sure, but that seems like a pretty reasonable explanation.

2. This is impossible to say either way. On clear, sunny day conditions, then the loss during the sweep will probably be larger than the gain in finding the new MPPT but that is usually when you need it the least. In variable weather conditions, the gain from finding the new MPPT will probably be larger than the cost of the sweep, and that is when you need it the most.

3. This is not currently possible for an end user to change. Sorry to say It is extremely unlikely that the firmware and software development time would be taken to make this into a user facing feature.

Now questions for you, how fast is your sample rate on that data? And what did you use to capture it?

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Matt Knight commented · Mar 19, 2019 at 12:24 AM

Thanks, @Guy! I figured it may the case that this was something of a micro-optimization and therefore unlikely to get prioritized. Just to double check though, there's no way to change this at all - even via the low-level HEX protocol for example?

As for your questions about our data capture, I'll try and summarize. We have a Victron CCGX with the MQTT broker enabled. We have a server machine running 24/7 which subscribes to the wildcard topic on the broker. It parses and records every message in an InfluxDB database which in turn is exposed via a Grafana dashboard (which is where the screenshot above is from). I'm using Node-RED to orchestrate that control logic.

Since the reporting frequency via MQTT can vary quite significantly, the server also publishes a R/ request on several key topics (e.g. battery voltage, current, etc) every 5s to ensure we have sufficient resolution. We're not doing that on the solar data yet, but I'll likely add that in very soon.

We were having some stability issues with MQTT so at some point I may bypass MQTT altogether and directly interface via the dbus. I've written a proof-of-concept but since then MQTT has remained stable.

Let me know if you have more questions - happy to share what we have.

0 ·

Modifications Space

Node Red Space

Answer 1 · 2019-03-19T00:45:02Z

markus answered · Mar 19, 2019 at 12:45 AM

Hi @Matt Knight,

"happy to share what we have"

Yes. This sounds very interesting. It would be great, if you write an article in the new "mods space"

launching-the-mods-space-a-new-section-on-communit.html

I am sure it would be interesting to many, if you could give a little bit of advise how to set this up.

Best Regards,

Markus

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Matt Knight commented · Mar 19, 2019 at 12:46 AM

Sounds good, will do!

1 ·

Answer 2 · 2019-03-19T00:53:22Z

sean answered · Mar 19, 2019 at 12:53 AM

I find it somewhat implausible that the MPPT sweep frequency is once every 10 minutes, and that 33 seconds is the period of time required to recalculate the new maximum power point.

Surely this isnt correct ?

15

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

markus ♦♦ commented · Mar 19, 2019 at 01:04 AM

I have connected one of my MPPTs to a hydro turbine, so I can listen and watch the MPPT algorithm ;o) I can also not confirm 33s sweeps.

But the readout is very interesting, maybe we get behind what those sweeps are about.

0 ·

Show more comments

ripper commented · Mar 19, 2019 at 09:02 PM

I can confirm every 10 minutes and it goes on " forever" ( never counted it, will do now) which is frustrating to see after a while. My logging is once every minute and it gets the low spikes pretty much all of them. Looking at the BMV which has much faster refresh cycles, it goes up and down on the watts multiple times when you would thinks twice should do the trick. I also record the solar panel voltage and there one can see when it finds a better spot. That is when most panels are in the shadows and one is completely not I think. Usually its sitting at 60 Volts, then it drops down to 30V.

0 ·

Show more comments

ben ♦ commented · Mar 21, 2019 at 08:56 AM

I can also confirm ~30sec every 10 minutes. The power is still pretty good within a lot of those 30 seconds, so it appears roughly to "cost" about 2% of produced energy when conditions are stable.

0 ·

Show more comments

Answer 3 · 2019-03-25T08:56:30Z

markus answered · Mar 25, 2019 at 08:56 AM

It seems that this behavior is spotted by more and more people.

spotty-drops-in-solar-generation.html

I had a chance, to have a close view on my solar setup this weekend. I don't have those sweeps...

But I have to mention, my solar charger is pretty oversized for my installation and it is only utilized by half of its load capacity at maximum yield.

Best Regards,

Markus

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

stepir commented · Mar 25, 2019 at 11:19 AM

Unfortunately VRM portal is not reporting anymore data from the last summer - I don't recall to have never seen those sweeps before this winter. I thought this was due to the new setup of my strings (moved from a single series of 10 panels to two series of 5 in parallel). Now could it be that this is due to a firmware or software change being done in this period of time (august 2018)?

My MPPT is well oversized as well, I have a 150/100 being used with roughly 1kwp.

0 ·

Matt Knight commented · Mar 26, 2019 at 03:20 AM

@Markus are you observing with VRM or your own monitoring? VRM only logs every minute so it may well miss those sweeps. Also, our own charger is oversized too - a 100/50 with 400W of solar panels connected.

0 ·

Answer 4 · 2019-03-25T09:32:05Z

rainerb answered · Mar 25, 2019 at 09:32 AM

Hello,

I can also see these "spikes" with my MPPT100-50 (every 10 minutes) and I have a direct comparison to my Fronius Galvo AC inverter.

My two PV arrays are directly next to each other on the same roof and same direction.

In my opinion these mppt spikes really annoys the ESS regulation. The sudden loss of mppt pv power often switches the inverter from charging to discharging and a few seconds later it feeds battery power to the grid until the ESS regulation is up to date again.

MPPT100-50 with spikes

Fronius Galvo with a smooth production (same date and time)

Best regards

Rainer

mppt100-50.png (18.8 KiB)

froniusgalvo.png (15.4 KiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 5 · 2022-03-24T19:32:03Z

custom answered · Mar 24, 2022 at 07:32 PM

Hello,

is there anything new on this issue?

I have also noticed the voltage drop every 10 minutes during a Bluebird day while my MPPT 75/10 is in bulk mode. I read the data directly from the VE.direct port.

Will this behaviour improved in future firmware versions?

Thanks!

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

maggi80 commented · Aug 10, 2022 at 05:33 AM

I would be very interested in a solution too. I have the same issue registered, when we have a day with totally blue sky. And my mppt drops about 1kW for the time of mpp tracking every 10 minutes. That brings my battery sometimes to switch from charge to discharge and my water heater is getting off when there is to low solar power

0 ·

20220810-073027.jpg (272.3 KiB)

kevgermany ♦♦ commented · Dec 12, 2022 at 09:04 PM

If you abandon tracking, it won't be there. But tracking is the essence of an mppt.

Note that the graphical display is affected by sampling frequency. Interesting that the current increases during the tracking period. And here that appears to be making the tracking period be shown larger than it really is.

0 ·

Answer 6 · 2022-10-14T19:15:49Z

Fra answered · Oct 14, 2022 at 07:15 PM

I am evaluating a controller with an almost flat efficiency curve at any power at 99%.

And a double mppt routine with 6,000 changes per second.

And a 30mhz processor.

I noticed that the victron smartsolar in boost-mppt seems to vary the voltage up and down a little faster than once per second.

also noticed that in case of partial shading of 33% of the panel longitudinally on purpose, the controller stays for 3 minutes on a false MPP losing 3/4 of power. (Negative fact).

Image Caption

Only after 3 minutes does it find the true mpp at about half voltage and recover all the power possible.

I also noticed a full swap of the voltage curve every 10 minutes lasting 10 seconds.

In my case last 10 second not 33 second.

Image Caption

And I noticed that in case of sudden load increase from no-mppt phase to mppt phase the controller performs 4 complete swaps of the voltage curve (positive fact).

Image Caption

Thank you

screenshot-2022-10-13-11-47-28-761-comvictronenerg.jpg (217.5 KiB)

screenshot-2022-10-13-11-47-32-289-comvictronenerg.jpg (217.8 KiB)

screenshot-2022-10-15-10-21-11-777-comvictronenerg.jpg (209.7 KiB)

screenshot-2022-10-15-10-21-04-314-comvictronenerg.jpg (207.1 KiB)

screenshot-2022-08-29-13-03-02-435-comvictronenerg.jpg (213.0 KiB)

screenshot-2022-08-30-10-16-30-134-comvictronenerg.jpg (213.2 KiB)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

klim8skeptic ♦ commented · Oct 14, 2022 at 07:39 PM

I also noticed a full sweep of the current curve every 10 minutes lasting 10 seconds.

Typo's.

Mppt adjust power op by varying pv current,

0 ·

Answer 7 · 2022-12-12T19:14:23Z

gerard-van-seventer answered · Dec 12, 2022 at 07:14 PM

Does anyone know a solution for this "issue"?

I'm having a SmartSolar Charger MPPT 250/70 (v1.59) with the same issue. Since energy is expensive and any watt counts I would expect a better mppt algorithm.

Here are my graphs with the issue.

And some more detail

--Gerard

mppt-dips-1.png (76.3 KiB)

mppt-dips-2.png (47.9 KiB)

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

kevgermany ♦♦ commented · Dec 12, 2022 at 09:08 PM

What issue? It's a natural part of tracking.

0 ·

gerard-van-seventer kevgermany ♦♦ commented · Dec 12, 2022 at 09:19 PM

The issue is that none of the mppt cycles results in a different/better volt/amp/power ratio. I think the algorithm is very course with a (relative) lot of wasted power. The "aggression" and interval of the mppt cycle should at least be configurable. In that way the end-user could adapt this behavior to their setup.

2 ·

question

Change MPPT Tracking Refresh Interval

Related Resources

question details

Modifications Space

Node Red Space

question

Change MPPT Tracking Refresh Interval

Related Resources

question details

Related Questions

Modifications Space

Node Red Space