question

Chris avatar image
Chris asked

Smart Blue Solar 100/50 producing half power for last 2 days

Hi all

over the last 2 days my Smart Blue Solar has started to produce half what it normally does.

Over the last week of good weather our Max Yield has been consistently over 1100w and 77v

yesterday and today 560w but still 77.9v

I noticed also the ESS was on, not by me as we are a ship and battery set to defaults not Traction as before.

I first Array which is very simular oin specs is working as expected, the only difference is the 100/50 is not the smart type as its 3 years old

Can anyone shed any light on what could be wrong with Array 2, the smart blue solar 100/50

many thanks as always

Chris

chargerservice
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

4 Answers
Paul B avatar image
Paul B answered ·

Hi Chris, we would need some screen dumps of the live readout and history page on both units as this would give us something to go by.

batterys full or near full and one array is keeping it topped up

bad connections on the array

wrong settings

bad connections from the charger to the battery,


Also try turning the other unit off and see if the smart solar output increases back up


1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Chris avatar image Chris commented ·

Hi Paul, thank you for the quick response

I will cycle the other unit now, just a thought though, It may have to do with the firmware update I did a few days ago, not sure if anyone else has had any issues


chris


0 Likes 0 ·
Paul B avatar image
Paul B answered ·

I dont think so, more than likley the batteries are full and one is in bulk and the other in float

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Chris avatar image
Chris answered ·

Hi Paul, check all connections and restarted 1000w array

still 1000w producing more than the 1200w

screen shot for 1200w array that has the faults

1000w array


Any ideas?


thanks again

Chris


1550413539075.png (35.7 KiB)
1550413599511.png (62.1 KiB)
1550413699045.png (73.0 KiB)
1550413747304.png (72.3 KiB)
1550414132837.png (63.0 KiB)
1550414175197.png (71.6 KiB)
2 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) avatar image Guy Stewart (Victron Community Manager) ♦♦ commented ·

The 1200W is showing a battery voltage minimum of 0V, do you know why that might be?

Also seeing charge times half that of the other array?

Can you isolate the panel strings into the 1200W, ie only allow half of the array and see if the power halves evenly for both sides independently.

0 Likes 0 ·
Show more comments
Paul B avatar image
Paul B answered ·

Please show the screen shots in smart power mppt controller

the live screen and the history

Use the victron connect app to display this on your phone or tablet

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Related Resources

Additional resources still need to be added for this topic