question

teloth avatar image
teloth asked

" Mandatory " Smartsolar update v1.56 killed VEDirect to VEDirect cable communication?

Early this morning I was presented with V1.56 " Mandatory " update on 150/60 Smartsolar that connects to my Multiplus II via VE direct port.


Immediately after the update finished , the controller vanished from VRM.


I have two other SmartSolar 150/35 , both of these are connected via VE.Direct to USB , that goes on a USB hub , that connects on the USB port on the MultiPlus II.


I have also updated both of these 150/35 to same V1.56 and both of them still reporting to VRM.


I swapped cables over , and 150/60 does indeed work on the VE.DIrect to USB.


Also tried the VE.Direct to VE.Direct cable on both of the 150/35 controllers , no joy, no connection.


So, this update definitely must have done somerhing that effects VE-Direct to VE.Direct link communication.


MPPT SmartSolar
1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

southsideph avatar image southsideph commented ·

I have upgraded both the camper and the show trailer to latest SmartSolar firmware 1.56. Connected to PI via USB to ve.direct without any issues so far

0 Likes 0 ·
3 Answers
teloth avatar image
teloth answered ·

Hi Matthijs

You should be a magician !

You made my SmartSolar appear again on Ve.Direct to VE.Direct cable :-)

Came home , had a nice ice cold beer to calm my general firmware update fears , done the V2.66 update on the GX and all is good now.

Many Thanks again


2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

seb71 avatar image
seb71 answered ·

Mine still work with VE.Direct cables after update to v1.56, but the difference is that I have a Cerbo GX, not a Multiplus II GX.


It would be a bizarre coincidence, but maybe check the VE.Direct cable you have.

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Guy Stewart (Victron Community Manager) avatar image
Guy Stewart (Victron Community Manager) answered ·

Hi @Teloth

Is this an official Victron cable with the Victron insignia, or a self-made cable?

If you are certain it is a genuine cable, please get in touch with your supplier about a replacement to see if that resolves the issue.

8 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

teloth avatar image teloth commented ·

Hi Guy and others for feedback.


Yes, the cable is a genuine Victron Ve.Direct to VE.Direct cable that has been in use for months and not has been touched.


Just to re-iterate couple of points, the VE.Direct to USB cable still works.

VE.Direct to VE.Direct cable does not.


Also , as I said , the moment the update is done , the Smartsolar 150/60 controller ( that was connected via VE.Direct to VE.Direct , on the single VE.Direct port that is on the Multiplus II ) , immediately disappeared from VRM and not obviously reporting solar yield which throws off Battery percentage values etc , even though charager still charges the battery.


I know it is weird but this is how it is.

The cable has not been touched whatsoever, it would be a trillion in 1 coincidence that it happened split second after update finished on the SmartSolar , cable not touched and this happened surely.

Can some more people see if after updating Smartsolar to V1.56 and see if VE.Direct to VE.Direct communication transmission still working and report please?

Thanks

0 Likes 0 ·
mvader (Victron Energy) avatar image mvader (Victron Energy) ♦♦ teloth commented ·

Morning! Sorry for the troubles!

I (a) tested several test systems like yours in our lab, ie. MP-II GX + MPPT with a VE.Direct connected MPPT, all work well.


and then (b) looked your system up in VRM. Where I noticed that your GX firmware is not the latest fw, its on v2.57. Could you update that?


v2.66 is the latest version iirc.


if that doesn’t work; I’ll make a support case and have someone help you with this in more detail (by logging into your system remotely, preferably).


we’ll get this sorted one way or another.

Matthijs


ps. for any one else reading this: there are already 100s of not 1000s of MPPTs running on v1.56. All OK, so I am not worried about a large systemic issue

0 Likes 0 ·
Show more comments