question

Fra avatar image
Fra asked

New victron agm battery accurate solar charging parameters

Hello I just bought a victron deep cycle 110 ah agm to replace the old battery after 3 years.
I would like to ask a Victron technician for the correct parameters.
I only use a solar charge with a fully configurable 30A mppt regulator.
Every day the solar energy is more than enuff to charge completely the battery. 
I discharge the battery every night on average about 20 ah.
I would like to know the correct absorption voltage and the correct duration of the absorption for my use (daily discharge of 20 ah).
Currently I have set 14.5v and absorption duration of 120 minutes with temperature compensation of - 4mV / C / cell. Floating 13.7v.
Today for example after the end of the absorption, the battery absorbed 0.8A in floating at 13.7V.
But trying to increase the floating to 14.5v, I saw that it went up to 2.6A. These is strange for me... 
Does that mean it wasn't fully charged? Or is it due to gas generation?
Then disconnecting the solar panel, after an hour the battery was at 13.5v, so it would appear to be fully charged.

The old agm, at the end of absorption, absorbed 0.8a for both 13.7v and 14.5v.
Why these difference on new battery? 
I can see all these parameters on the victronenergy smartshuunt.
MPPT Controllersbattery chargingVRMAGM Battery
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

2 Answers
Paul B avatar image
Paul B answered ·

I have attached the full data sheet for you as well

1618025640563.pngDatasheet-GEL-and-AGM-Batteries-EN.pdf


3 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Fra avatar image Fra commented ·
thank you very much ... I had already read that document. but it says 14,2-14,6 .... what do I put exactly? Is 14.5 a good compromise for my light use? and the floating? what do i choose between 13.5 and 13.8? 
Regarding the absorption time, I would like to manually copy the algorithm of the smart solar charger, i.e .: 
11.9V <Vb <12.2V 4h 12.2V <Vb <12.6V 2h Vb> 12.6V 1h. my solar mppt charger epever tracer does not have the adaptive function, but I have to set the time manually. usually my battery in the morning is always> 12.6, so 1 h. 
is it useful to do a light refreshment \ equalization once a month? I was thinking like this: discharging the battery to 50% and charging at 14.9v for 2 hours? or is it harmful or useless?
0 Likes 0 ·
Paul B avatar image Paul B Fra commented ·

for me if you have the batteries in a HOT area/climate then use the lower voltage settings.

you DONT equalize AGM or GEL batteries EVER


the more cycles the battery do the more harm is done

0 Likes 0 ·
Show more comments
Fra avatar image
Fra answered ·
thank you very much ... I had already read that document. but it says 14,2-14,6 .... what do I put exactly? Is 14.5 a good compromise for my light use? and the floating? what do i choose between 13.5 and 13.8? 
Regarding the absorption time, I would like to manually copy the algorithm of the smart solar charger, i.e .: 
11.9V <Vb <12.2V 4h 12.2V <Vb <12.6V 2h Vb> 12.6V 1h.
 my solar mppt charger epever tracer does not have the adaptive function, but I have to set the time manually. usually my battery in the morning is always> 12.6, so 1 h. 
is it useful to do a light refreshment \ equalization once a month? I was thinking like this: discharging the battery to 50% and charging at 14.9v for 2 hours? or is it harmful or useless?
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.