question

ishtiaq avatar image
ishtiaq asked

Narada battery setting

6V&12V operation manual copy.pdf

Hello

lets give a full details of the system configuration

Easysolar 5kv

BMV 712 smart

3 Battery balancer

9 X 375wat solar panels

3 string 12v 200ha Narada 313F HTB " I'm attaching the operation manual "

my concern is charging current setting for 48v system 25c

Float 54.40v / Equalization 56.4 this is according to operating manual

no details any where in the user Manual regarding Absorption charge current noticed, what would be the most suitable charge current, noting the max discharge is 10 -15% of the battery capacity regards .. ishtiaq

48v battery
6v12v-operation-manual-copy.pdf (3.1 MiB)
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

4 Answers
alan avatar image
alan answered ·

Different manufacturers use different terminology for the same thing.

Narada are especially bad at this, equalisation in this case is the absorption charge voltage and current.


real equalisation voltage for a Lead Acid battery is around 2.5-2.7v depending on the type.

Those cells don’t require equalisation.

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

ishtiaq avatar image
ishtiaq answered ·

Thanks Alan

I agree Narada such pain in this case, your given information is good enough to remove the confusion about the equalization and absorption charging , but in other hand if you look at the user manual stated to do equalization for 24 hr, kindly look under Charge requirement

I'm really concern to to do either equalization or absorption for 24hr

noting MPPT already take care of the absorption the setting is 2.30min

your feedback highly appreciateed

2 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

alan avatar image alan commented ·

I assume that you are going to be using these in cyclic operation? Ie power source at night and charged from solar.

As stated here, http://narada-ap.com/wp-content/uploads/2016/06/12HTB100.pdf

Cyclic charge is 2.3/cell @ 35c with -5mv/C temp compensation, which works out at 2.35V/cell @ 25c.

I would ignore the timing if used in cyclic operation as it is more relevant if they are used in float, I.E in a ups or something that might cycle once a year. As for current stick to 0.2C10, so 120A if you have 600ah capacity and you will be fine, the data sheet linked above quotes unlimited current under 25celcius or 0.25C10 above 25celcius

0 Likes 0 ·
ishtiaq avatar image ishtiaq alan commented ·

well noted and many thanks for your valuable advice

0 Likes 0 ·
marc-de-montreal avatar image
marc-de-montreal answered ·

hi, go to page 11 table 3-2 voltage setup which charging voltage depend of the load current.. in my opinion, absorbing is a state which current fall slowly near zero at the charging voltage set point.. that help you?

note: china products traduction is often erratic.. have you tried to contact them?

Marc

1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

ishtiaq avatar image ishtiaq commented ·

Hi marc

Thanks for your time, seeting on page 11 table 3-2 apply for BLVD and LLVD series mine is HTBF

Yes I have tried to contact them and I received the operation manual -:)

(absorbing is a state which current fall slowly near zero at the charging voltage set point.. that help you?) I can't really tell that's what seeking help here and safe battery lifetime

0 Likes 0 ·
michelg avatar image
michelg answered ·

Hi Ishtiaq, as far I have seen on internet your batteries are either AGM or Gel, thus they don't need to be equalized. This will lead to a failure, as there is no way to replace the electrolyte. They are not lead-acid battries where you can refill them with distilled water. So, equalization is a no go !

Michel

10 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

ishtiaq avatar image ishtiaq commented ·

Hi Michel

its sealed lead acid, 313 HTB series and with regards to the equalization this is clearly mentioned in the operation manual

anyway thank for your time and writing

ishtiaq

0 Likes 0 ·
Show more comments

Related Resources

Additional resources still need to be added for this topic