question

gilemon avatar image
gilemon asked

Grid feed in excess power not working anymore in ESS (keep batteries charged) mode

Hi,

After I have replaced my Smart Solar 150/85 with a brand new VE.can rev2 model, the ESS Grid Feed-in option does not work anymore in "keep batteries charged" mode.

screen-shot-2021-01-23-at-41104-pm.png

screen-shot-2021-01-23-at-41115-pm.png

The system is attached to the grid most of the time and I'm using the batteries for UPS application.

Basically when batteries are fully charged, the MPPT does not output any power anymore.

screen-shot-2021-01-23-at-40944-pm.png

If I disconnect the grid input momentally and I reconncet it so that the batteries get recharged, I can verify the PV and charger output some power.

screen-shot-2021-01-23-at-35113-pm.png

Also with the old Smart Solar 150/85, this function was working perfectly.

I have no DVCC and this is what's shown on CCGX under SmartSolar MPPT VE.Can 150/85 rev2 > Networked operation tab:

screen-shot-2021-01-23-at-40430-pm.png

So far I tried:

  • Updating CCGX firmware to latest 2.6.
  • Changing battery monitor from BMV-700 to Quattro

but nothing helped. What am I missing?

Let me know if you need more information about the configuration.

ESS
screen-shot-2021-01-23-at-35113-pm.png (150.8 KiB)
screen-shot-2021-01-23-at-40430-pm.png (95.7 KiB)
screen-shot-2021-01-23-at-40944-pm.png (147.5 KiB)
screen-shot-2021-01-23-at-41104-pm.png (81.4 KiB)
screen-shot-2021-01-23-at-41115-pm.png (72.5 KiB)
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

1 Answer
gilemon avatar image
gilemon answered ·

It has been a month now and I'm still in same situation.

I have tried "Optimize, and set the minimum SOC to 100%" but it is oscillating constantly. When battery is fully charged it starts using inverter (MPPT/solar + batteries) after 5 seconds it recharges the batteries, then after 5 seconds for a moment (1 second) it does not use MPPT anymore. This dance makes the battery balances go crazy. It does not seem healthy to me.

I also tried enabling DVCC (I had to upgrade Multi firmware to v481), without any change.

The only way I found to force using all the solar input, is by cutting the grid input and forcing battery discharge for 10s. After this the solar is used again to charge the battery back. And after it reaches 100% the excess solar it used in the Multi again.

This is quite annoying because I need to constantly monitor the ESS/CCGX and still this leads to a lot of wasted solar energy.

11 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

seb71 avatar image seb71 commented ·

Not sure what is the cause (except maybe the new MPPT, since you say that your system worked perfectly with the previous MPPT), but try "Optimized without BatteryLife" in ESS and set the minimum SOC lower than 100%. For instance 85%. Then see if it works as it should and then go from there.

0 Likes 0 ·
Show more comments

Related Resources

Additional resources still need to be added for this topic