question

Mike Salaru avatar image
Mike Salaru asked

Smart Battery Protect says OUTPUT DISABLED BY REMOTE

Smart Battery Protect says OUTPUT DISABLED BY REMOTE and because of that I can't use any of the 12V devices.


Can someone advise as to why there is no power going out to my 12V distribution board from the SBP100?

And the same why no power going to the Battery from the SBP200 ?

Both are saying that they have been "Output Disabled by Remote"


Many thanks



1. SBP100 for load disconnect

2. SBP for Load disconnect


3. SBP100

4. SBP200

5. BMV readings.

6. As you can see the negative voltage is coming to the negative feed of the 12V distribution. And 12 V positive feed going to SBP "IN" field, but nothing goes out to the loads.

7. VE.BUS BMS

8. SBP flashing lights

Lithium BatteryBMSBattery ProtectVEConfigure 3VE.Bus
whatsapp-image-2020-10-28-at-230301.jpeg (181.1 KiB)
whatsapp-image-2020-10-28-at-223418.jpeg (35.0 KiB)
whatsapp-image-2020-10-28-at-223105.jpeg (29.8 KiB)
whatsapp-image-2020-10-28-at-223048.jpeg (30.0 KiB)
whatsapp-image-2020-10-28-at-220335.jpeg (30.3 KiB)
whatsapp-image-2020-10-28-at-220311.jpeg (29.6 KiB)
whatsapp-image-2020-10-28-at-230655.jpeg (146.0 KiB)
whatsapp-video-2020-10-28-at-230029.mp4 (14.9 MiB)
whatsapp-video-2020-10-28-at-215407.mp4 (511.1 KiB)
1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Mike Salaru avatar image Mike Salaru commented ·

The second picture made a mistake, it's for SBP200 for Charge disconnect (from solar mppt and sterling).

0 Likes 0 ·
1 Answer
Matthias Lange - DE avatar image
Matthias Lange - DE answered ·

You have connected the BMS signal to the "L" pin of the remote, you have to use the "H" pin.

Take another look at the manual.

8 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Mike Salaru avatar image Mike Salaru commented ·

I have made the changes, and the "OUTPUT Disabled by remote" is still there, any other suggestions? Thank you

P.s: on a side note, why is the SBP100 showing a different voltage to the SBP200? In victron connect9f41b3d1-b7a4-4310-8e57-b9c09b56e328.png

a3965a3f-c21f-43f2-aefb-23258726ab9a.pngc8b9dd74-3d90-4d9a-ad0c-71c743997f53.jpeg2dd0ec25-281c-4bb6-8537-9ff3768ec583.jpeg

0 Likes 0 ·
2dd0ec25-281c-4bb6-8537-9ff3768ec583.jpeg (2.1 MiB)
c8b9dd74-3d90-4d9a-ad0c-71c743997f53.jpeg (2.1 MiB)
a3965a3f-c21f-43f2-aefb-23258726ab9a.png (126.1 KiB)
ad0d9f6a-6033-4df2-b202-c012f9315c1b.png (126.3 KiB)
2f79f987-7406-467c-bcd8-449d54039bf5.png (126.1 KiB)
9f41b3d1-b7a4-4310-8e57-b9c09b56e328.png (126.3 KiB)
Show more comments
Mike Salaru avatar image Mike Salaru commented ·

It worked, thank you !

0 Likes 0 ·