question

gunnadoo avatar image
gunnadoo asked

Mppt 150/70 grounding issue

I have an mppt 150/70 connected with bmv700 , Phoenix 24/12 converter and Phoenix multiplus 24/3000 Recently had cable melting issues on the 12v side and rewired everything.

All 12v accessories ground to the Orion Not the chassis

The 24v house battery bank is also not grounded to the chassis . If I connect the 12v or the 24v black wire to the chassis it goes up to 17v and wires get warm And the Mppt 150/70 reads 0v on the Pv side if I keep the 12or 24v floating (not grounded to chassis all is ok and the POV voltage shows again charges etc

I have a smaller mppt on the 24v starter batteries which also has a 24/12v converter for audio system but these appear to be fine and have no influence even though they are grounded to the chassis of the bus.

It seems that only the mppt 150/70 has issues and therefore anything 12v inside the bus cannot use a earth to chassis anymore hence the rewiring.

Although it all appears to work properly now it has me scratching my head any thoughts?


John

MPPT Controllers
1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

gunnadoo avatar image gunnadoo commented ·

Addendum : When I disconnect the charging side of the mppt I can ground 12 and 24v to chassis with no problems. It’s when I reconnect the mppt to batteries it introduces an extra 5 v causing issues and PV output shows 0v so I think there’s an issue with the mppt which is my main concern the current workaround is ok but it’s what the mppt does

That’s the issue

0 Likes 0 ·
5 Answers
markus avatar image
markus answered ·

It sounds a bit like there is a short circuit between the pv connection and the chassis.


5 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

gunnadoo avatar image gunnadoo commented ·

Exactly that’s what I’m trying to work out as I have eliminated everything else by recabling everything using floating ground method

0 Likes 0 ·
Show more comments
gunnadoo avatar image
gunnadoo answered ·

Confirmed everything reconnected and all works as intended amazing one missing ground lead caused over 30hrs of rewiring and testing etc . At least I now know where everything goes and what it does and I have added extra fuses and breakers along the way

VICTRON is still king of the hill in my books


2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

markus avatar image
markus answered ·

Hi,

to help you in this matter, I think you have to provide more accurate information on what exactly you would like to connect.

Maybe you can make a drawing of your installation.

As I read this, I hope you use good and quick fuses.

Markus



1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

gunnadoo avatar image gunnadoo commented ·

I’ll do a drawing as well pls see my additional note

0 Likes 0 ·
markus avatar image
markus answered ·

There are 2 versions of the Orion converters. Isolated one and non-isolated one.

The non-isolated one share the same minus.

1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

gunnadoo avatar image gunnadoo commented ·

Correct I have non isolated one

0 Likes 0 ·
gunnadoo avatar image
gunnadoo answered ·

Problem solved ??? I isolated a pv so the frame did not contact the chassis no change still -16.5v

I then connected another earth (black) lead from the Orion’s common shared earth terminal to the chassis and all is ok showing 13.2v now instead of -16.5 the mppt 75/15 is still charging so I’ll reconnect all the panels to the mppt 150/70 go figure.....

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Related Resources

Additional resources still need to be added for this topic