question

sunshine avatar image
sunshine asked

advice re victron 12v system

Hello,

Looking to do the following on a cheap budget for a farm bound friend who is currently burning dinosaurs (geny) at a rate that makes me cringe.

120-130A/hr dc usage at 12V a day


so he likes 12v because he understands it so being a remote farm i want to keep it 12v nominal at the batts.


I can get 175w victron 12v panels locally too was going to wire 3 in parallel down to a dc breaker then to solar regulator. (will make leads esy to follow for him and ill use colour shrink on pv cables so he can easily identify the pos/neg of each panel should he need to remove one as result of damage.



so i was going for

3 x 175 victron mono panels Reference No. SPM041751200

bluesolar PWM yes PWM (remember cheap) sub tropical location too has display and charge his phone via usb thus (Saving $200 over the MPPT this covered the 3rd panel) I figured 525watts via PWM would outperform 350watts via MPPT.

800w victron inverter

360 a/h battery bank

12/30 victron charger

I know its only 3 days carry over only but he must run a stock pump for a few hrs every few days so ive added a victron 12/30 battery charger so when hes burning dinosaurs he can top up bank if required .


so thats back ground for you all

now to my question ... the PWM says 36 cell panels are best used but the 12v victron panels are 72 cell even though they are 12 v ??? are these still suitable ??


Am i silly to use the PWM ..after reading the white paper and everything else I could find it seems that 12v nominal systems are the go right up the 30A limit which will be right on for him. and as said the $200 saved has paid for the additional 175 watts.

cable runs all calculated for less than 3% voltage loss more like 1-1.5% as everything is pretty close together.


all fusing and breakers are dc rated so all covered on the saftey front.


Just that lingering 36 v 72 cell 12v panel question.


I could buy 2nd hand 24v pv panels and the MPPT but after many hre drive to set this up remote Id rather give him good new gear from victron and ensure I he has no issues.


thoughts


Future expansion is not and going to happen .... and 240v ac usage will always be kept to bare minium hence the smaller inverter.


Thanks for reading

victron products
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

1 Answer
klim8skeptic avatar image
klim8skeptic answered ·

Hi Sunshine,

I have like a mobile beach shack (truck) that I have fitted out with solar, with a bit bigger array than you are anticipating.

About half of my consumption is for 12v appliances (TV, computer, stereo, lights, water pumps, tiny 10L HWS, phone/laptop/tablet chargers).

A have some 230v ac loads, refrigerator, tiny kettle, tiny hot plate, tiny skillet, microwave, clothes washing machine.

My goal was to us as much free energy (solar) before using LPG, or petroleum.

So far 16 months into my off grid lifestyle, I have not had to plug in, or top up. Gas usage has been 2 x 9kg bottles, mostly for cooking in winter, no petroleum (generator) so far.

My winter solar harvest/power consumption has been between 1.5-2.0 kWh a day (about 120-150 Ah@12v).

Summer solar harvest/power consumption goes up to 2.0-3.0 kWh a day. Extra power consumption over summer goes into the refrigerator, and 230v cooking. (No heating required from gas cooking over summer)

So I have said my system and arrays was a bit larger.

100/50 mppt with 4 x 190w panel. 2S x 2P. Flat orientation.

75/50 mppt with 3 x 190w panel. 3P. E/W orientation.

300 Ah lithium battery.

12/1600/70 multiplus.

A BMV700, Venus gx and a buttload of BMS/battery safety/monitoring stuff.


For your farmers project, I would advise a 100/50, with a full set of panels. Second hand panels are a bargain, just keep an eye on the condition they are in.

I would use an 800w multiplus over the inverter and charger combo, simply based on cost. (providing an 800w unit does what is required)(multiplus's can be a bit funny on generators though)



winter-solar-harvest-consumption.jpg (41.2 KiB)
summer-solar-harvest-power-consumption.jpg (41.5 KiB)
img-20190915-121214390-hdr.jpg (3.3 MiB)
6 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

sunshine avatar image sunshine commented ·

Thanks for your reply and your truck looks awesome.. on the panel array front did you fuse each panel within the string ..reason i ask is seems that if using a parallel connection of panels 3 or more would require individual fusing ..I was going to use mc4 branch connectors and bring all 3 panels down a to a dc rated 2 pole breaker..


going individual inverter and charger so he can use the charger on other things around the farm and its more geny friendly as you say.


still not sure about the victron 175w being 72 cells..

0 Likes 0 ·
Show more comments

Related Resources

Additional resources still need to be added for this topic