question

gavin-andrews avatar image
gavin-andrews asked

MPPT voltage and current jumping around late in Absotption stage

We have an EasySolar 48/5000/70-100 with CGX, BMV, lead acid battery bank (460Ah) and 2600W of solar panels. It is a fully off-grid, residential installation.

I noticed a strange issue today. During the low-amperage tail of the absorption cycle, the MPPT voltage and current started to fluctuate rather wildly. I will attach a VRM image of the data, with the issue starting at around 1330hrs. It has been a perfectly clear day, with not a cloud in the sky. The current plot from the inverter indicates there were no unusual loads at the time.

Has anyone else encountered this and what may its significance be?

mppt charging
1588516963261.png (119.1 KiB)
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

3 Answers
Daniël Boekel (Victron Energy Staff) avatar image
Daniël Boekel (Victron Energy Staff) answered ·

Hi @Gavin Andrews

do you have a screenshot of the power use graph? maybe this is caused by fluctiations in power use?

6 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

gavin-andrews avatar image gavin-andrews commented ·

The only power output is to the AC system and here is the chart of A.C. use over the same period.

0 Likes 0 ·
screenshot-2020-05-04-10-37-25.png (69.6 KiB)
Daniël Boekel (Victron Energy Staff) avatar image Daniël Boekel (Victron Energy Staff) ♦♦ gavin-andrews commented ·

Hi @Gavin Andrews

ok nothing strange there. can you show:

-charge state of MPPT when this happens? (make a screenshot with both Voltage / Current and MPPT state visible please)

-MPPT settings

0 Likes 0 ·
Show more comments
boogymanxxl avatar image
boogymanxxl answered ·

Hallo Gavin, ähnliche Probleme habe ich auch. Nur die Lösung fehlt mir noch.

Vielleicht prüfst Du mal folgende Einstellungen:

VictronConnetAPP> Schweifstrom, ReBulk-Spannung

Eventuell Schweifstrom abschalten und eine hohe ReBulk Spannung wählen. ( 5.2V wird für eine 48V Bank in anderen Foren berichtet)


Frage von mir:

Welche Ladespannungen hast Du im Multi eingestellt (über VEconfig) ?

und welche Ladespannungen hast Du im MPPT eingestellt (über VictronConnectApp) ?


Konntest Du dein Problem lösen...?

LG Lars

1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

gavin-andrews avatar image gavin-andrews commented ·

Hi there. Sorry, I don't speak German.

0 Likes 0 ·
ripper avatar image
ripper answered ·

I had this several times too. Only found it in the higher bulk or abs voltage. PV Watts go from near zero to near 100% within seconds and back and overshoots by over a volt of desired voltage. That is too much for my AGM batteries I should think. It's an Mppt 100/20 on 24V and there was no fluctuating load attached.

It goes back to doing it when disabling/enabling the maintenance charger setting via ve connect. Only thing helped was taking off all the wires or presumably a night of rest.

I remember playing around with the generator and charger early in the morning while the pv charger was already operational before at least one event. Usually I charge at nighttime so that was a special occasion. Maybe that threw it off hours after?

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Related Resources

Additional resources still need to be added for this topic