question

Jerry L Johnson avatar image
Jerry L Johnson asked

Dvcc with incompatible firmware #48

Just installed 5.21 beta VictronConnect. It upgraded my mppt smart solar to 1.48. my color control has a notification error

system warning Dvcc with incompatible firmware #48

what should I do about this error message?

gx devicesmart solar charging behaviour
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

6 Answers
Mark avatar image
Mark answered ·

It is unusual that the MPPT FW upgrade has caused GX error #48 - was the CCGX FW also maybe upgraded recently?

This error can occur when upgrading to a recent Venus OS FW (v2.40 or later) and when one of the system devices does not meet the minimum DVCC firmware requirements.

I would recommend to take a look at the current FW version of all other devices in your system (CCGX, Inverter/Charger, Battery Monitor and also managed batteries) and then determine what may need to be updated.

4 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Jerry L Johnson avatar image Jerry L Johnson commented ·

I just noticed I received two emails from VRM during the firmware upgrade.

1. DVCC Firmware insufficient alarm: Warning

2. DVCC Firmware insufficient alarm changed from 'Warning' to 'No alarm'

maybe I’m ok?

0 Likes 0 ·
Jerry L Johnson avatar image Jerry L Johnson commented ·

thank you for the reply.
I have a BMV-712 and a smart solar 100/50 along with the color control GX.

i upgraded the gx a few days ago.

all three are at the latest firmware.

0 Likes 0 ·
Mark avatar image Mark ♦♦ Jerry L Johnson commented ·

In that case my 'guess' is that the MPPT would have been offline for a minute or so during the MPPT FW upgrade and that could have (maybe) triggered the temporarily error.

What about your inverter/charger - is that a Victron unit and if so what FW is it running? (if you have one)

And do you happen to have lithium managed batteries?

0 Likes 0 ·
Jerry L Johnson avatar image Jerry L Johnson Mark ♦♦ commented ·

My inverter and charger are separate stand alone unmanaged units. I rarely use the charger since the solar does such a great job.

i have four Battleborn 100amp hour lithium batteries that are managed by themselves other than the mppt.
thank you again for your response.

Im also thinking this was a temp error during the mppt upgrade. Just hasn’t happen with past upgrades.

0 Likes 0 ·
c2519028 avatar image
c2519028 answered ·

I have the same issues after upgrading my MPPT 150/35.

8 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Rob Duthie avatar image Rob Duthie commented ·

Hi All

Yes upgraded Easysolar 3kw 48v and Multi plus2 3kW parallel system and after undating all firmware to the latest for all the units and MPPT in the Easysolar returned this error as well?

Regards

Rob D

NZ

0 Likes 0 ·
JohnC avatar image JohnC ♦ Rob Duthie commented ·

Hi @Rob Duthie

This issue is listed in the VenusOS changelog for v2.63 as "fixed". Maybe try that if you haven't already..

0 Likes 0 ·
Rob Duthie avatar image Rob Duthie JohnC ♦ commented ·

Hi John C

I will check the the Venus ver again, i though when i did the firmware update to 481 for the Easysolar GX inverter it updated the GX device, looks like it does'nt.

I will update this next now i see that on the version was still stuck at V2 .60.

Regards

Rob D

NZ

0 Likes 0 ·
Show more comments
c2519028 avatar image c2519028 JohnC ♦ commented ·

I have V2.63 and get the message.

0 Likes 0 ·
Show more comments
Rob Duthie avatar image Rob Duthie JohnC ♦ commented ·

Hi John C

All done and OK now, no errors.

Regards
Rob D

NZ

0 Likes 0 ·
matejs avatar image
matejs answered ·

I got this alarm too after upgrading firmware. I got it also at previous upgrade via Victron Connect.

I have:

- CCGX v2.54

- MultiPlus-II 48/3000/35-32, firmware 456

- SmartSolar Charger MPPT 150/35 v1.50

- Bluetooth Smart Dongle

- AGM batteries


I guess the requirements are met, but why I get this error?


2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

drdiesel avatar image
drdiesel answered ·

I also have 2.63 and get this message with all devices on the latest firmware.

1 comment
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Rob Duthie avatar image Rob Duthie commented ·

Hi

Need to update the CCGX to the latest Ver 2.63 as ther is a issue with older version.

Look in the change log it advisea about this issue #48.

Regards
Rob D

NZ

0 Likes 0 ·
Rob Duthie avatar image
Rob Duthie answered ·

Hi

Also do the hardware update as well to comply.

Regards

Rob D

NZ

2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

pierre-joubert avatar image
pierre-joubert answered ·

I'm getting the same issue, the firmware versions are:


CCGX V2.63

VE,Bus 481

Bluenova Battery V3.6

SmartSolar MPPT VE.Can 250/100 rev2 V3.04

Sunspec PV Inverter 0004.0011.0030


Regards

2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Related Resources

Additional resources still need to be added for this topic