question

drumond avatar image
drumond asked

Why is the Cyrix Li CT draining my battery?

Hello,


I thought the Cyrix Li Ct would charge only my 200Ah auxiliary lithium battery in my van.


When I switch on the van engine, it reads 14.2V on my starter engine (the starter battery is an old one, I will replace it next month) and 13.58V on the Lifepo4 (around 50% charge at this very moment).

Or when I turn off the van engine, it's also the other way around, the lifepo4 is depleting and charging my engine battery (they tend to have the same voltage as soon as I switch off the engine, around 13.1V each). I don't want that to happen at all.

It is like my Cyrix Li Ct was useless. For information, I also have a Ve.bus BMS. Everything is plugged like it is shown on the connection diagram given by Victron.

How can I prevent the Lifepo4 to NOT charge the starter battery when the engine is turned off?

Do I have a defective Ve.bus BMS or is it the Cyrix Li Ct that doesn't work properly?


Thank you.

Cyrix Battery Combiner
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

2 Answers
Matthias Lange - DE avatar image
Matthias Lange - DE answered ·

A cyrix works in both directions, but you maybe have to wait a moment:
https://www.victronenergy.com/upload/documents/Datasheet-Cyrix-Li-ion-120-A-EN.pdf

If you want it goes only from the alternator into the lithium battery you should use a DCDC-charger.


cyrix-li-ct.png (16.0 KiB)
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

drumond avatar image
drumond answered ·

30 minutes later, there was still current going from the Lifepo4 to the starter battery... and the voltage of the Lifepo4 read around 13.15V.

I had to disconnect manually the two batteries between them.

Can the VeBus BMS have something to do with it? There is a cable between the VeBus and Cyrix Li Ct for Charge Disconnection. could the VeBus BMS be faulty too, or is it necessary the Cyrix Li Ct only. Can I test it by manually injecting 12V-13V in the Cyrix Li Ct Charge Disconnect port? I don't know if that would be risky?


Thank you.


EDIT: I unplugged the ground in the Li Ct and there was the sound as it was opening the circuit. Plugged again, tests, now it seems to work as it should do. I am going on with the tests. Everything is ok for now........

12 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Matthias Lange - DE avatar image Matthias Lange - DE ♦ commented ·

Under normal conditions the charge disconnect port of the BMS is high.
It becomes low/free floating if a cell voltage gets to high or the temperature to high/low.

If you disconnect this wire (or the gnd wire) the cyrix must open.

0 Likes 0 ·
drumond avatar image drumond Matthias Lange - DE ♦ commented ·

I can recall it opened when I disconnected it. But by disconnected the ground a short instant and rewire it now everything seems to work. I have just made a batch of trials and everything works like a charm for now. It looks like it had been stuck internally before I discovered the ground wire, I really don't know why it wouldn't work initially.

0 Likes 0 ·
Show more comments