question

airpress89 avatar image
airpress89 asked

MPPT 150/85 VECan

Hello.

I use a 48V battery system

My charger was running without problems with 2 Jinko Solar panels in serie for almost a year.(+-35v each pv) (around 70v in full sun, that's wat the controller said) Today I connected a third one. The MPPT showed a voltage from around 105v. (good margin as the controller can handle 150v "open pv voltage"

For a resaon it does not show the current coming from the pv. Other words it does not charge.

When I disconnect the third panel. It works great again with 2 panels. I reconnected the third one, same thing.

I'm missing something?

48volt charging
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

2 Answers
dc-marine avatar image
dc-marine answered ·

Have you tested the new panel by itself ? Use a clamp meter to confirm output by measuring short circuit current (clamp your meter around the leads and plug them together to short the panel and read current in full sun, you can safely do it for a few seconds, long enough to get a reading). Also check open circuit voltage.


Also unlikely but double-check polarity of all panels. Also make sure the MPPT wants to enter bulk mode by power cycling (turn off both PV and battery connections).

1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

airpress89 avatar image airpress89 commented ·

Okay, I will test it with the clamps today if it's gonna be full sun today in Belgium; ;-)

Another thing I get in my head now.

I didnt connect the ground to the third panel because I wanted to do a test with a 3 one?Can this be the issue?

0 Likes 0 ·
airpress89 avatar image
airpress89 answered ·

Hello

Shorting the panel result in around 36v short circuit. Looked at the solar panel information paper and that a good reading. Also the short circuit current in full sun was around 14/15amps.

Also, the MPPT wants to enter bulk mode by power cycling That works also.


Can it be that the solar charge controller is not capable for 48V systems and 3 panels?(open circuit more then 100v) Are there Victron engineers here that can confirm this?


Edit: I did the mppt calculator test, my controller is capable of working with that configuration. In fact, it's capable of working with 3(435Wp) panels in serie and 4 strings.

9 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

klim8skeptic avatar image klim8skeptic ♦ commented ·
@Airpress89 What is the Model and serial # of the mppt?
0 Likes 0 ·
airpress89 avatar image airpress89 klim8skeptic ♦ commented ·
150/85 Ve.Can A10D

Serienummer: HQ201883CP6

0 Likes 0 ·
klim8skeptic avatar image klim8skeptic ♦ airpress89 commented ·

@Airpress89 Check your mppt against the model # at the bottom of this thread.

0 Likes 0 ·
airpress89 avatar image airpress89 klim8skeptic ♦ commented ·
Thx!

Ohhh, What it’s only a 12/24v model? Why does the mppt calculator on the victron site choose this model of i select that I have a 48v system?

0 Likes 0 ·
klim8skeptic avatar image klim8skeptic ♦ airpress89 commented ·

@Airpress89 What it’s only a 12/24v model?

Only the 4 model / part numbers I linked to.

0 Likes 0 ·
airpress89 avatar image airpress89 klim8skeptic ♦ commented ·
These are suitable with only 12/24v you linked?
0 Likes 0 ·
Show more comments

Related Resources

Additional resources still need to be added for this topic