This site is now in read-only archive mode. Please move all discussion, and create a new account at the new Victron Community site.
I'm about to uprgrade my inverter charger from a 12 / 1600 / 70 to a 12 / 3000 / 120 will it need to be set up to the system i.e. batteries etc if so can it be set up on a phone using blootooth or will it require connection to a laptop / computer. Is the inverter charger easy to set up. Thanks
I forgot to mention that this inverter charger is going to be used on a narrowboat
You will need an MK3 to USB adapter (https://www.victronenergy.com/accessories/interface-mk3-usb ) and ve.config with a laptop to configure if you'd like to directly connect to the inverter.
or
You can use a ve.bus smart dongle (https://www.victronenergy.com/accessories/ve-bus-smart-dongle ) and Victron Connect app on your smart phone.
I haven't used the smart dongle yet, but I know that not 100% of the features are there yet. However basic programming should be doable with the smart dongle, but I still think it's a good idea to have a MK3 to USB in your kit.
@LesRollins, you'll need the MK3 to USB adapter and a Windows-based computer; you'll need either the VictronConnect app and/or the VE.Config tools on the computer to program the new Multi. If your settings are pretty basic, the new VictronConnect app for Windows can be used to configure every basic setting, but is you're needing to use Assistants, you'll need the VE.Config tools.
As @nebulight mentioned, you can get the smart dongle for it, but it's basically useless as far as any settings go... you can view information, but you really can't change anything.
Alternatively, all the really basic settings can be set via dipswitch if you really want to get into it, but I highly recommend using the MK3 adapter and a computer, it's much much easier.
Basic setup is pretty straightforward... after you have the app on your computer and you connect the Multi to it, you're looking at probably 10 minutes to set it up unless you have complex configurations that you're getting into.
@Justin Cook Victron has put a lot of work into the Victron Connect app recently so you can do a lot more with the smart dongle now. Load up a demo device in the app and you can see what you can do with it. The gap is closing between the two methods.
With that said, you need to be on firmware 415 before you can use it, so I stand by my statement that it's still a good idea to have a MK3 adapter as you'll need that to update the firmware if you aren't current.
Hmmm I'll have to do some inspection, @nebulight... our display Multi is connected to a CCGX, so the settings available on my phone through the smart dongle are basically nil, I'll have to try disconnecting the CCGX and seeing if I can access the full feature set now. Thanks for the heads-up!
Just open a Demo Multi in Victron Connect
You can change many settings there except the relay function and assistants.
@Justin Cook It's not clear in the manual, but there is a section on Modes of Operation:
https://www.victronenergy.com/live/vebus_smart_dongle_manual#modes_of_operation
It doesn't clearly state programming abilities but states what can be done with the dongle with a GX device is on the network.
Thanks for that guys. What settings will I need to change apart from landline set to 16 amps and the battery configuration which is float 13.50 bulk 14.82 absorption 14.70 for a maximum of 4 hours and equalization 16.20. Taken from the trojan website regarding there T105s 6v batteries. @ Justin Cook @ nebulight
I always suggest setting low voltage shut down limit as I think the default is really low. I also set my charge current to match the battery bank size as the 3000 has a 120amp charger which may be too much for a smaller battery bank's long term health. I have lifepo4 and I never charge above .5c. You might want to check the specs of your battery for suggested charge currents.
@nebulight what charge current would you suggest for a 675 amp battery bank
