question

fli037 avatar image
fli037 asked

EVCS cannot communicate with Cerbo gx

1000023452.jpgI have connected today EVCS to existing Victron installation that comprises 3 Multi ii 5000 VA in a ESS config, a Fronius gen 24 10 kW on Multi AC out, an MPPT and 32kWh Pylontech battery bank.

EVCS is connected on Multi AC in and configured in the same network with fixed ip 192.168.1.158.

Cerbo GX ip is 192.168.1.227 (lan cable) and 192.168.1.85 (wifi)

EVCS detects Cerbo GX both ip's and VRM id but when i press Check it gives an error that it cannot communicate with Cerbo GX on any of the 2 ip's.

I have enabled TCP Modbus on Cerbo GX and I can detect the EVCS ip and the device is saved.

I have updated Cerbo GX firmware to v3.32

EVCS firmware is updated to v.1.28

I have tried to whitelist the Cerbo GX ip's in EVCS setting without success.

I have restarted Cerbo and EVCS several times...

Reset of EVCS to factory settings and seup again did not help.

EVCS can charge the car manually but the figures displayed are not correct in EVCS webpage and on VRM (AC power 0, battery 0).

When EVCS in auto, although I was exporting 11kW to the grid the message was "waiting on sun".

Can someone help me?

VRM portal ID: c0619ab3c264

1000023433.jpg

1000023432.jpg

1000023430.jpg

1000023429.jpg

1000023428.jpg

1000023436.jpg

cerbo gxModbus TCPevcs
1000023433.jpg (393.5 KiB)
1000023432.jpg (432.1 KiB)
1000023430.jpg (522.7 KiB)
1000023429.jpg (571.3 KiB)
1000023428.jpg (442.9 KiB)
1000023436.jpg (325.3 KiB)
1000023452.jpg (485.7 KiB)
1 comment
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Lucian Popescu (Victron Energy Staff) avatar image Lucian Popescu (Victron Energy Staff) ♦♦ commented ·
Hi, can I take a look at your system?
0 Likes 0 ·
2 Answers
Lucian Popescu (Victron Energy Staff) avatar image
Lucian Popescu (Victron Energy Staff) answered ·

You have to enable Modbus TCP service, it is disabled
1716964038550.png


1716964038550.png (4.2 KiB)
22 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

jchowdhury avatar image jchowdhury commented ·
Hi Lucian

I have the same problem and have tried many ways with no luck. EVCS can see the Cerbo on its dashboard but Cerbo GX cannot find the EVCS. I've added EVCS IP manually and Modbus TCP is enabled but still no luck.Cerbo version 3.32, EVCS version 1.28. I've been stuck in this condition for many months. please let me know how can I fix this

0 Likes 0 ·
Lucian Popescu (Victron Energy Staff) avatar image Lucian Popescu (Victron Energy Staff) ♦♦ jchowdhury commented ·

are both devices in the same network?

0 Likes 0 ·
jchowdhury avatar image jchowdhury Lucian Popescu (Victron Energy Staff) ♦♦ commented ·
Yes same network
0 Likes 0 ·
Lucian Popescu (Victron Energy Staff) avatar image Lucian Popescu (Victron Energy Staff) ♦♦ jchowdhury commented ·
what's the IP address of each device? Is there any router between them ?
0 Likes 0 ·
Show more comments
jchowdhury avatar image jchowdhury Lucian Popescu (Victron Energy Staff) ♦♦ commented ·
Hi, how can i change my username please, it shows my email as username ?


0 Likes 0 ·
Lucian Popescu (Victron Energy Staff) avatar image Lucian Popescu (Victron Energy Staff) ♦♦ jchowdhury commented ·
the username is "admin" and cannot be changed. Not sure what you mean by email address.
0 Likes 0 ·
Show more comments
jchowdhury avatar image jchowdhury Lucian Popescu (Victron Energy Staff) ♦♦ commented ·

This is from the EVCS dashboard

1717069272996.png



0 Likes 0 ·
1717069272996.png (83.5 KiB)
fli037 avatar image
fli037 answered ·

Indeed, Modbus TCP service was disabled. Works now!

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.