question

houser avatar image
houser asked

Could Victron do wind too in the future?

Hello,

Could Victron relatively easily add wind modes for the current crop of MPPT smart controllers?

As companies like Midnite Solar have added useful wind and water modes to their regular solar controllers, I was wondering if Victron might consider doing the same in the near future?

I would assume I am not going to get any clear answers on this, but have been building a regular solar system with Victron mppt controllers and VRM and am very happy with it.
In adding a wind turbine the obvious path would be something that ties into the same system flawlessly. Grateful for any hints ;)

MPPT ControllersVRM
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

6 Answers
wkirby avatar image
wkirby answered ·

I agree, they should have a product to tap these types of generation.
There are lots of wind controllers out there, but as far as I can tell, only Midnite currently offer the system integration which I also think is quite valuable.

I think that they could add more features than the Midnite offering, easier configuration just one of the things that come to mind including Venus and VRM integration, of course.
There are probably a lot more features they could add to make a really good wind / hydro unit.

2 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

houser avatar image houser commented ·

Thanks WKirby,

Good to know others are thinking along these lines.

I am buying a wind controller soon regardless. But maybe the next one..

0 Likes 0 ·
kai avatar image kai ♦ commented ·

Personally I'd be interested in such an option as well, able to program in an arbitrary profile and feedback ouputs so they can essentially be interfaced to virtually any generator. In an ideal scenario, even the algorithm can be tweaked (obviously that would have go in as non-official mod).

0 Likes 0 ·
houser avatar image
houser answered ·

Just a friendly bump if there is anything at all on the horizon regarding this..
Still looking for this gear for our existing Victron GX solar setup. Many thanks for any hints or feedback if there is anything on the market that fills this void yet?

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

markus avatar image
markus answered ·

Hi @houser,

if Victron was to make such a product, what features should it have, how much should it cost?

Would you mind and share some of your thoughts here?

Best Regards,

Markus

4 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

imutt avatar image imutt commented ·

@Markus

Since I am searching for possible options to add windpower into a Victron based system, I offer some "wishes" on what a product line could look like:

- Different models of MPPT for power up to 400w and up to say 3kw wind turbine

- 12/24/48V capability

- Physical Dumploads

- Connectivity into GX/Venus/VRM.

- The key part is intelligent integration with Multi/Quattros and other charging devices on the system. It should be a trivial setup to configure a prioritization of charging like "Consumption loads -> charge battery 100% -> enagage external trigger (heater core until tempsensor reaches threashold) -> engage dumpload". Today - my understanding is that such a configuration is border line possible without using external automation outside the realm of Victron VRM.

- The price point should ideally be slightly less than comparable power for solar MPPT, due to the higher cost of windturbines vs solar panels over the life span and the lack of simple expansion. Adding a few more solar panels when the economy allows is something different than getting another big turbine. The cash up front is significantly higher for wind power.

Cheers!

1 Like 1 ·
houser avatar image houser commented ·

Hello Markus,

Well I of course have no deeper understanding of what would be possible to do with software only on current hardware, but if possible, just adding wind and perhaps water modes to the current line of smart solar chargers would make sense as an entry point? If possible, "just" add smart wind power curves and allow editing in the VRM so they appear in the VRM as non-solar sources.
That would have been sufficient for me at present, just using a diode to convert the AC to DC and then use it as is. This already works, but is not terribly efficient so far in my current setup.

The benefits for integration and charge synching and such are probably obvious.

The next level would perhaps be new units that allow physical direct AC inputs and also standard things like RPM, windspeed, braking and perhaps dumploads and such. But I am sure others would have more specific ideas about what would make sense from a market perspective.
The price points would perhaps be similar to the solar version for small to medium wind turbines. Larger stuff is well beyond my area of knowledge.
Hope this helps.

0 Likes 0 ·
markus avatar image markus ♦♦ houser commented ·

Thank you!

0 Likes 0 ·
lucode avatar image lucode commented ·

Not sure if there is an easy solution that would fit the many available turbines out there. I guess the simplest solution would be to just use the recommended DC (24/48V) out controllers of the turbine manufacturers and use a DC shunt to get all the data that goes into the battery. I had a look at the following low-cost Peacefair PZEM-017 V/A meter and it seems suitable. There even exists a solution to connect it to a Venus device via Modbus.
https://github.com/mildred/venusos-peacefair-pzem
But as I'm not yet experienced in hacking a Venus device I'm a bit careful before I would like to jump into this adventure.
So if Victron would include and improve this solution into the Venus stack, it would be an easy way to connect all kinds of external sources into GX based energy system. And of course into VRM, so they appear in the VRM as non-solar sources.

0 Likes 0 ·
ripper avatar image
ripper answered ·

I would assume the load output couldt be programmed as a dump load or as a driver of say a battery protect as relay to short cut the generator and thereby brake it? Isn't that almost everything necessary to drive a tiny generator?

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

David avatar image
David answered ·

I am interested in Wind like others on this thread and as a forerunner have installed a local IP-enabled weather station so I can monitor and see if it could be a viable option at my location (it certainly seems windy enough!)


This is really just an observation ... I used to use a product called the Power Integrator PI25C, made by Amperor Associates, a small company based in Scotland. This was a combination B2B Charger and MPPT Controller.

This device supported up to 200W of "renewable" power via two separate inputs, one dedicated to Solar, and one dedicated to Wind (both used simulaneously)

However ... the Wind input could just as easily be used for another Solar Panel (and that is how I used them both on Campervans - one 100W PV Panel into each connection).

This product used to retail at around £160 (and I used to get them trade at under £100) for a Combo B2B/MPPT/Solar Charge-Controller (a super price!)

So my point really is that it cannot be that complex to add Wind Support on to an MPPT controller and it also must be able to be done at minimal cost if this company could do it at such an affordable price.

Sadly, Amperor Associates are not around anymore, but their product WAS good and I never had issues with them.



pi-front.jpg (34.1 KiB)
3 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Mark avatar image Mark ♦♦ commented ·

So when the batteries were full and wind speeds were high, was this particular charge controller able to 'dump' the excess power somewhere to limit the wind turbine from over-speeding and/or prevent over-voltage?

This is the more dangerous aspect of wind / hydro and the more difficult aspect to deal with and regulate.

Also during charging the charge controller ideally needs to keep the turbine operating in the peak efficiency region to get the most out of it.

Once this is done the final conversion to the correct battery charge voltage and profile is the final and easy part.

0 Likes 0 ·
David avatar image David Mark ♦♦ commented ·

As I said, I used both connections for PV, so I wouldn't know from personal experience, but as it was designed to work with Wind, I would imagine they had considered that aspect, no?

0 Likes 0 ·
Show more comments
Steve Byrne avatar image
Steve Byrne answered ·

I have a Bornay wind turbine, and chose it because their Wind+ MPPT uses modbus, and they seem to have a completed driver to allow the turbine to work with GX devices, though for some reason they don't seem to have made it a default option despite being Victron distributors themselves. I'm currently trying to get Bornay to help me get it working on my own setup. The MPPT they offer will support 12/24/48V DC output, and a 220V AC input, and has internal dumps. It will run up to 6000W. Presumably any Victron product would need a fairly wide input range, and a customisable power curve, but there are plenty of people out there running small turbines and there is definitely a need for a product like this.


2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.