question

Hi @spicedreams I know that your question has been around quite some time, but as I had a similar scenario and could not totally follow the other answers, here is what I concluded:

* The RS Inverter SmartSolar does not have an AC output _and_ AC input, but only a single AC connection, on which it generates its sine wave. This is in contrast to the "Multi"-family that have dedicated inputs and and outputs, where the input synchronises its sine wave from an external source if available and then either passes this through or generates its own sine wave.

-- > (from an AC perspective) so when connecting the RS Inverter SmartSolar to the input of the EasySolar, the latter will pick up the frequency and consider this input as any other input (such as grid or generator). I do not see a way to connect them the other way round (but this was also not something you were asking).

However, as far as I understand Victron this is _not supported_ though _technical possible_.

- you would cascade or "daisy-chain" both inverters and with PowerAssist (or PowerControl, I always mix these up) the EasySolar would be able to deliver its own 3000VA _plus_ the maximum 6000VA (depending on temperature and voltage, see also below) to the loads which would _all_ be connected to the output of the EasySolar.

- there will be not power feedback from the EasySolar to the RS Inverter SmartSolar. So the EasySolar does not behave as a grid-tied PV inverter and the "factor 1" rule would not apply. And there should be no frequency shifting on the RS Inverter SmartSolar either that would affect the EasySolar.

- I have never tested when both chargers (and the MPPT charger of the EasySolar which is technically a separate device) are connected via DC to the same battery bank. But you would have to consider that all devices charge the same time and that they do not communicate on what they are doing (such as accidentically overcharging the battery). You might want to use a relay to stop one device from charging at a SoC that is much lower than the other one. The maximum charge current and maximum discharge current has to be considered as well (is the combined maximum of both chargers higher than the battery can handle at any given load and temperature?). But again, I do not know if this can work at all.

- sudden changes in load might more easily lead to overloading.

- the AC input of the EasySolar needs to be "fixed" to a certain maximum input current (less than the maximum output of the RS Inverter SmartSolar. This can only be adjusted in 0.5A or 1.0A steps. So, in order not to overload the RS Inverter SmartSolar you would need to choose a value depending on the maximum temperature you are expecting. The data sheet shows minimum values from 3000W (~3750VA) @60°C, 4500W (~5625VA) @40°C and 4800W (~6000VA) @25°C. So "safe" values would range from 16A to 26A. But this in turn would lead to a probably nearly always higher utilisation of the RS Inverter Smart and its battery, but in turn never be able to provide its full power. Higher utilisation will also have a lower efficiency (meaning you burn more power) and drain your batteries on that inverter faster. On the other hand the EasySolar will only really invert with loads higher than the RS Inverter SmartSolar can supply. This will lead to batteries that are more seldomly used on that inverter. Plus, the EasySolar would try to constantly charge its own batteries from the RS Inverter SmartSolar batteries (as it seems to be "grid-connected). Some thoughts on that: With one of the "recent" firmware updates and the "Prioritise other energy sources" option you could try to change that behaviour (not to charge all the time, but I never used that feature). Or, depending on your EasySolar-connected battery you could try to toggle "allow-to-charge"/"allow-to-discharge" on your battery based on a certain SoC. "Inverter only"-mode will not help here, as then the AC input seems to be ignored completely. Or lastly (as I did), use the MultiPlus assistant. There is the "Virtual Switch" with the "dedicated ingore AC load" option. This lets you use AC input on the EasySolar based on load and SoC.

- when cascading the inverters the EasySolar and to each output an RCB is added, the likelihood of tripping it might increase.

- the RS Inverter SmartSolar has a VE.Can connection and can be connected to the GX, but I do not know how this works together with the EasySolar. As there is only one global DVCC option that would control both chargers it might be better not to integrate them into a single GX but maybe use an separate GX if you plan to connect your BMS to the GX as well.

That being said, I have a similar setup running and working without problems for a couple of months now, but I know this is _not supported_ but it is technically possible (in addition, I have a DC/DC charger so I can shift power between batteries either way when needed).

If anyone spots a mistake or disagrees I am happy to hear about it.