question

ernstsl avatar image
ernstsl asked

Battery Protect dis- and reconnect voltage with new LifePo4-battery

Goodday to all of you,

I just installed a brandnew Lithium 200Ah battery, and as you probably can imagine, I would like to treat it as good as possible ;-)

Attached two photos: the charcing/discharging settings that came with the battery, and a menu item of my BP 12/24v 65A.

Do the discharging-settings really mean I can enter this voltage in the BP? So disconnect at 10V, reconnect at 12.6v?

Especially this 10V seems so low…. Is it better to stay at the safe side and enter a slightly higher voltage? It will decrease the output of course, but the last thing I will is damaging this expensive battery.

Thanks for your advice!

Ernst

img-0473.jpeg

img-0474.jpeg

Battery Protect
img-0473.jpeg (4.1 MiB)
img-0474.jpeg (497.4 KiB)
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

5 Answers
Alexandra avatar image
Alexandra answered ·

@Ernstsl

You can't charge through the battery protect. Just making sure you know that.

10v is what your battery manufacturer system the BMS will shut down at. So that is what they call safe.

You can go a bit higher if you would rather have the loads off before the battery shuts down.

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

ernstsl avatar image
ernstsl answered ·

@Alexandra

Thanks for your quick and clear response! I do not charge trough the BP.

So it is safe to set the disconnect voltage to 10V, as the manufacturer states.

I’m new to batteries with build-in BMS, learning every day ;-) I understand now the battery will shutdown by itself at 10v as well. So too deep discharging is not possible thanks to a build-in BMS? Does such a BMS make to use of a BP-device less usefull? Apart from better two protections then one, possible.

And if I decide to put the disconnect voltage on the BP a bit higher as you suggest? What would you recommend? 0,5v higher, or less?

Thanks again!

Ernst

4 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Alexandra avatar image Alexandra ♦ commented ·

0.5v is ok. It will allow for cell imbalances as well.

Some batteries shut down earlier than 10v if one or two cells run too low as a protection.

Are you batteries actively or passively balanced?

If they are passive balanced them make sure they get 100% every few days and stay in absorption to allow cell balancing.

0 Likes 0 ·
ernstsl avatar image ernstsl Alexandra ♦ commented ·
Hi @Alexandra , thanks again!


Your writing batteries in plural, I’ve only one battery. I’ve read some about balancing but it seems to deal with more then one battery in the system.

If you refer to some proces in the internal of the (one) battery, I honestly couldn’t tell you if there are actively of passively balanced.

Regards,

Ernst

0 Likes 0 ·
Show more comments
Nev avatar image
Nev answered ·

300Ah 4 cell Sinopoly LiFePO4 battery with no internal BMS.

9 years of full-time travel. The battery also starts our motorhome 3.9l turbo diesel engine.

These are our now at least 7 year old BP65 settings:

screenshot-20231008.jpg

Apart from the occasional test it has never triggered.





screenshot-20231008.jpg (46.7 KiB)
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

grahamwood avatar image
grahamwood answered ·

I wouldn't allow the battery BMS to shut down the battery coz you will have no DC power to the charge controllers which might still be getting some panel voltage. They don't like that.

I would use the BP to shut down at 12.5 volts to cut off the loads but connect the charge controllers from the battery side of the BP.

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

ernstsl avatar image
ernstsl answered ·

@Grahamwood Thanks! As a matter of fact I read in the manual about the estimated SOC and voltage a very gradual decrease of voltage; from 100% 13.6v to 9 % still at 12.6v. From 9 to 0% is goes down to 10v.

So this makes sense referring your opnion. After all, if I put the disconnect-value of the BP at 12,5, I only “miss” the last 10%. Which would be better anyway not to let the battery drain that deep.

Greetings,

Ernst

2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.