question

jonathan-drewes avatar image
jonathan-drewes asked

SmartSolar Fixed Abs Time Incorrect

For my SmartSolar 250/60, I use a fixed absorption time of 15 min and tail current is disabled. This worked well, no problems.

Now that I have added a 150/45 and new PV array to the system, I set that unit to have the same settings as the 250/60. I was expecting a 15 min abs time to occur but now get only 3 min for both units. I need it to be 15min for the battery I am using. Both MPPTs are feeding the same Lifpo4 battery.


Any idea why this happening?

The manual states--

1690229465151.png

which implies that I should be getting the set 15 min.

Here are the settings I have on both MPPTs--

1690229929291.png


see, 3min, not 15

1690230083859.png

1690230121521.png



Any ideas gang?

Thanks!





MPPT SmartSolar
1690229465151.png (40.1 KiB)
1690229929291.png (24.9 KiB)
1690230083859.png (13.8 KiB)
1690230121521.png (13.3 KiB)
3 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

klim8skeptic avatar image klim8skeptic ♦ commented ·
@Jonathan Drewes more details plz.

VE Can model mppt's?

Using DVCC?

VE Smart networking?

Does a BMS control charging? What BMS & battery?

From the screen shot, BMS controlled = YES. A new feature?

0 Likes 0 ·
Show more comments
2 Answers
jonathan-drewes avatar image
jonathan-drewes answered ·

So, disconnecting the Bluetooth smart network solved the issue here. In watching the 2 units charge on the VictronConnect screen, they do seem to be in sync, letting one unit deliver the abs charge but both say they are in the same state.


THANK YOU ALEXANDRA !!!!



2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

jonathan-drewes avatar image
jonathan-drewes answered ·

Also, both MPPTs are using v1.61 firmware.

Cerbo-S is v2.92 if that matters.

5 comments
2 |3000
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvas avatar image mvas commented ·

Have you tried ...

  • Shut down the PV power
  • Shut down the Battery power.
  • Wait a minute
  • Enable Battery power
  • Enable PV power

See if that solves the problem.

0 Likes 0 ·
jonathan-drewes avatar image jonathan-drewes mvas commented ·
No, but I'll try that. Not sure how that could help but maybe it does.
0 Likes 0 ·
Alexandra avatar image Alexandra ♦ jonathan-drewes commented ·

Disable the smart network, you have a GX the two aren't designed to work together.

See limitations point2.

Bms control should only be on if your BMS is comms (can or other) connected.

2 Likes 2 ·
jonathan-drewes avatar image jonathan-drewes Alexandra ♦ commented ·
OK, I will try that and report back.

I do not understand why this should be disconnected though. Dont we want to have the V and i shared from my smart shunt to the Mpps so they can get a more accurate reading?

0 Likes 0 ·
jonathan-drewes avatar image jonathan-drewes Alexandra ♦ commented ·

Alexandra, what about this from the intro page?

1690311868051.png

0 Likes 0 ·
1690311868051.png (13.8 KiB)