question

Bato & Co avatar image
Bato & Co asked

Easy Solar 2 GX and BMV

Hello from France,


I recently started to work on a future setup for my new boat (where I live). I plan on using a Easysolar 2 GX with a 1.6Kwp PV and a DC/DC Orion to charge via the alternator.

Is it possible to connect a BMV 712 via V.E direct to the Easy Solar 2GX? I wanted to double check because it is stated in the manual that there's 1 V.E direct but the MPPT built in is via V.E direct.

Also, in the manual of the Easysolar 2 GX, they talk about a "battery monitoring" system, is it "kinda" the same as the BMV series? I mean % battery, Ah consummed etc...

The whole electrical system will be in the bilge and I would like to have a visual clue without having to open the bilge or checking my phone (even though I love the Bluetooth functions and the VRM) that's why the BMV. It is possible and may it cause troubles to the battery monitoring built in the Easy Solar 2 GX?

Thanks very much for your time.

Baptiste

BMV Battery MonitorEasySolar All-in-OneBluetooth
1 comment
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

kevgermany avatar image kevgermany ♦♦ commented ·
If you can avoid installing in the bilge, do. Water and electrical installations are not good.
0 Likes 0 ·
2 Answers
klim8skeptic avatar image
klim8skeptic answered ·

@Bato and Co it looks like there is a spare VE Direct socket available for the BMV, top left of pic.

EasySolar GX 2 connections.

The batt monitor in the multi does not measure dc currents from solar chargers or to dc loads. You are better using a BMV for accurate SoC.

2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Bato & Co avatar image
Bato & Co answered ·

@kevgermany If there's water in my bilge, it won't take long for the boat to be at the bottom lol but thanks !


@klim8skeptic Thank you for the answer. So BMV is my go-to as I thought. I don't want to degrade the batteries and after lots of reading, having a SoC via BMV is a good choice. Do you have any Idea if there is a way to use the internal relay of the BMV to activate/deactivate the inverter?

At a SoC of any% switch on the shore power and reverse?

Again many thanks, really helpful

8 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

klim8skeptic avatar image klim8skeptic ♦ commented ·

@Bato and Co Do you have any Idea if there is a way to use the internal relay of the BMV to activate/deactivate the inverter?

Sure you could use the relay in the BMV to switch the multi off via the multi's remote port. Once off though you lose the ability for the multi to recharge the battery.

You could use the AC Input Control feature within Victron Connect, to connect / disconnect the AC input. You will need a Mk3 USB adapter to program the multi . This can be based on the battery voltage, or the multi's battery SoC monitor (the 1 that is not so good with DC current).

ac-input-control.png

Any thing more complex will require a GX based system.

1 Like 1 ·
ac-input-control.png (289.4 KiB)
Show more comments
kevgermany avatar image kevgermany ♦♦ commented ·
Bilges are damp...

On the relay, yes it can switch on SOC. Configuring it is easy and covered in the downloadable manual.

But it's for low power.


0 Likes 0 ·
Show more comments