Venus OS v3.00~4 available for testing

Question

replit

This site is now in read-only archive mode. Please move all discussion, and create a new account at the new Victron Community site.

This question was closed Dec 22, 2022 at 08:37 PM by mvader (Victron Energy) for the following reason: ther eis a newer test version now.

question

mvader (Victron Energy) asked Oct 25, '22

Venus OS v3.00~4 available for testing

Hello there!

A brand new version is available for testing, for the first time. Don't over read into the v3.00 designation though, its that just because its the next in line. Not because we're doing some more than normal changes.

Introduction to Venus OS beta testing

In case you don't know what this message is about, please start with reading this link, which explains the Venus OS beta program. Venus OS is the software running on all our GX devices, such as the Cerbo GX.

How to post an issue?

Please keep all findings organised as answers to this question. One answer per issue. So first check the existing threads. If you have the same as someone else already reported, welcome to add a comment saying "me too". And preferably some more details. And in case its not listed yet, add a new Answer. Note that Answers and Comments are two different things!

Lastly, please first revert to the latest official release (v2.92), to double check if the issue you're seeing was present there as well. Regressions require a different treatment than other issues and bugs.

Changes, compared to latest official release (v2.92)

For systems having multiple BMSes connected, allow selecting which one should be used for DVCC. It also allows the use of a BMV for SOC tracking -- by selecting BMV as battery monitor -- while still using the BMS for DVCC. A bit of a niche issue for special systems, more technical background here: https://github.com/victronenergy/venus/issues/901 (but please don't start posting on our github - thanks).
Detect Hubble batteries, untested as of yet.
Add Polish translations, thank you Jakub T for helping with that!
ESS: increase control speed of systems using todays supported meters (ET112, ET330, EM24, and also the ABB ones) a little. But, for faster meters, such as the EM540 which is not available yet, increase it very significantly. Requires updating the built-in MK3-chip, see next bullet.
Include a newer version of onboard MK3-chip firmware. Updating that has a 1 to 10% chance of a short system outage (Multi/Quattro shuts down in VE.Bus Error 14, restarts after 30 seconds). And therefore the update needs to be initiated manually from within the menu. Note that this is a reversible action, no need to worry about being unable to roll back. After updating, and then rolling Venus OS back to v2.92 or some other earlier version, the MK3 will automatically (and silently) be downgraded to the for that version of Venus OS required MK3-firmware version.
Improve text for tank sensor name in pump configuration.
ESS: Fix bug where PV is not used for loads when scheduled charging to 100% during daytime
Fix bug where a PV-inverter on AC-in-2 would not be shown in the ESS overview. The workaround was to configure the PV inverter as being on AC-in-1. Not needed anymore.

Venus OS Large

Fix issue sometimes causing certain values to update slower than necessary.
Add client_max_body_size to nginx config for larger flows.
Update nodejs to v14.17.6, which is the latest v14.17.* LTS. Change log here: https://github.com/nodejs/node/blob/main/doc/changelogs/CHANGELOG_V14.md#14.17.6

Under water / developer

Various small under the hood changes, mostly resulting in small reductions of CPU load
Replace Hiawatha webserver with nginx; which is better kept up to date (security)
Include various OE Dunfell fixes
DVCC: simplify transmission of the charge voltage setpoint by sending it always, rather than only if devices that work with it are detected. This won't make a difference to any commonly known system type.

Ps. Here are a few screenshots related to that MK3 firmware. On systems not updated yet, you'll see this (after going to the Device list, and then into the MultiPlus, Quattro or EasySolar listing):

And for anyone wanting to make sure its updated, in that same menu, scrolling all the way down to the Device submenu, and going in there, and scrolling down again, you'll find this listing:

Wherein the 212 digits are the version number, and thats the old one. And here is what you see after the update:

Venus OS

1666825009093.png (99.3 KiB)

1666825094337.png (84.9 KiB)

1666825165306.png (86.2 KiB)

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Mike Dorsett commented · Nov 07, 2022 at 06:46 PM

For systems having multiple BMSes connected, allow selecting which one should be used for DVCC. It also allows the use of a BMV for SOC tracking -- by selecting BMV as battery monitor -- while still using the BMS for DVCC. A bit of a niche issue for special systems,

With respect to systems with multiple BMS units, surely the system needs to look at ALL of them for computing DVCC limits. If any one BMS demands a reduction in charge current - this will be due to cell imbalance - then the charge current needs to be reduced. Similarly with discharge limits.

1 ·

Jaco Reinecke commented · Nov 18, 2022 at 05:40 PM

ESS: Fix bug where PV is not used for loads when scheduled charging to 100% during daytime.

Think I was one of the first to report this ... years ago.

I'm so testing it. Been a HUGE bearbug of mine for years now. 100% SOC and then the panels just drop away, sometimes. Happened today again, I upgraded on the spot.

0 ·

Modifications Space

Node Red Space

Answer 1 · 2022-10-25T18:24:04Z

pau1phi11ips answered · Oct 25, 2022 at 06:24 PM

Is the ET110 meter a typo? You mean ET112?

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Oct 26, 2022 at 11:35 AM

Hi yes indeed, thanks @pau1phi11ips , corrected

0 ·

Answer 2 · 2022-10-26T14:44:51Z

derrick thomas answered · Oct 26, 2022 at 02:44 PM

Large os you mention an update to the latest nodejs...just wondering if this adds any new functionality such as new victron nodes, or additional functionality for existing victron nodes? I sure would like to see some more control over settings in the victron output nodes.

5

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Oct 26, 2022 at 10:48 PM

Hi Derrick, no it doesn't add such functionality. Nodejs is one of the underlying frameworks; not related to Victron at all. See also here for changes: https://github.com/nodejs/node/blob/main/doc/changelogs/CHANGELOG_V14.md#14.17.6.

What settings are you looking to control from node-red?

0 ·

derrick thomas mvader (Victron Energy) ♦♦ commented · Oct 27, 2022 at 01:57 AM

I can read the ac input type from the victron system node (I assume this specific node reads the cerbo gx system settings? It states that it retrieves info from com.victronenergy.system dbus path) but I don't see any way to write to the com.victronenergy.system dbus path in order to change the ac input type thru node red. I am using 2 MP2 in parallel and would like to be able to write a node red flow that will change the ac input type between shore or generator based upon a digital input signal from the generator. Would be nice to see separate energy consumptions in vrm for each input.

0 ·

mvader (Victron Energy) ♦♦ derrick thomas commented · Nov 04, 2022 at 08:33 AM

Hi @derrick thomas , sorry, but that is not possible. Doing that will require a firmware change in the inverter/charger, and even though I understand what you want and like it myself as well, there are other priorities for at least the coming 6 months or longer.

0 ·

fguiot derrick thomas commented · Nov 04, 2022 at 06:00 PM

Hi Thomas, this is exactly that problem that is addressed with my simple solution, calling a shell script from Node-RED. See here: https://community.victronenergy.com/questions/166788/solution-displaying-correctly-the-ac-source-genera.html

0 ·

derrick thomas fguiot commented · Nov 05, 2022 at 03:24 PM

Checking it out now thanks. Does this method survive Venus updates?

0 ·

Answer 3 · 2022-10-26T18:15:00Z

jetronic answered · Oct 26, 2022 at 06:15 PM

What is meant by the onboard MK3 chip?

I have a USB MK3 adapter on my PI, do I have to load the a firmware update on the adapter?

3

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

juf commented · Oct 26, 2022 at 06:47 PM

@Warwick Bruce Chapman

can you pls explain your comment.

is there a way to update the usb mk3 adapter with the RPI running Venus os.

regards

0 ·

mvader (Victron Energy) ♦♦ juf commented · Oct 26, 2022 at 11:01 PM

Hey both @jetronic and @Juf : the onboard MK3 is a microcontroller built-in into our normal commercial products, like Cerbo GX and Venus GX.

For those having a RaspberryPi + MK3-USB, you'll also be able to update the firmware, which then is in that MK3-USB.

I've added a few screenshots above to make clear where you find the update option in the menu; and or if you don't, how to check the firmware version of the MK3.

2 ·

juf mvader (Victron Energy) ♦♦ commented · Oct 27, 2022 at 05:06 AM

Thanks :-)

0 ·

Answer 4 · 2022-10-26T18:37:17Z

Warwick Bruce Chapman answered · Oct 26, 2022 at 06:37 PM

MK3 Firmware updated on HQ21286P26K with no outage.

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Oct 26, 2022 at 10:51 PM

Thanks Warwick

0 ·

Answer 5 · 2022-10-26T21:58:53Z

nebulight answered · Oct 26, 2022 at 09:58 PM

"Don't over read into the v3.00 designation though, its that just because its the next in line."

1666821511456.png (406.3 KiB)

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Oct 26, 2022 at 10:52 PM

smile

1 ·

gainestr mvader (Victron Energy) ♦♦ commented · Oct 27, 2022 at 12:22 AM

I’ve actually seen versions run into the 100’s 200’s and even higher before but I think the newest update warranted a new v3 release.

0 ·

Answer 6 · 2022-10-27T05:36:01Z

dirk-s answered · Oct 27, 2022 at 05:36 AM

One feedback from me: I just installed the new version on my Multiplus II GX 5000 with a EM24 Modbus and Pylontech batteries. It is a ESS System. The regulation speed before was around 20 - 25s for a load of 2.400W.

The regulation speed after update increased significantly. It needs around 5-7s now and I observe a speed of around 400w per second. This is the speed which is requested at least by German grid rules as far as I know. I'm very satisfied with this update! Thank you for this improvement.

Directly after update of MK3 firmware I can observe the increased speed of actualization of the EM24 power values. Some values per second now.

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:31 AM

great feedback, thanks.

0 ·

Answer 7 · 2022-10-27T08:14:47Z

nickdb answered · Oct 27, 2022 at 08:14 AM

In the case where you parallel a non-updated mk3 firmware multi with one which has been updated, will that update prompt reappear?

3

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

jeroen ♦ commented · Oct 28, 2022 at 03:54 PM

It won't reappear, if you agree that it is fine to update them, all of them will.

0 ·

nickdb ♦♦ jeroen ♦ commented · Oct 28, 2022 at 05:38 PM

The question is about expanding an existing system that has already been updated by adding one that hasn’t been.

0 ·

jeroen ♦ nickdb ♦♦ commented · Oct 28, 2022 at 08:37 PM

as said, the message won't reappear, but it will get updated.

0 ·

Answer 8 · 2022-10-27T09:42:46Z

markus-001 answered · Oct 27, 2022 at 09:42 AM

The nginx webserver hands over to different access points far better than the Hiawatha Webserver did, I would even go as far as to say seamless now, the Hiawatha Webserver took some effort to get reconnected on certain access points, I had to constantly disconnect completely from the Wi-Fi, (forget Wi-Fi) then re-join key in the Wi-Fi password again to get the nodered dash board working again. Tested this at two sites both handing over perfectly now.

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:30 AM

Thank you Markus! nice to hear.

0 ·

Answer 9 · 2022-10-27T09:58:31Z

markus-001 answered · Oct 27, 2022 at 09:58 AM

The ET112 grid meter speed is defiantly faster I could reduce the grid set points to get closer to net zero on the grid meter by 10w on a 10kva quatro and 40w on a 2 x 5KVa multi plus II running in parallel.

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:30 AM

Great, thanks.

0 ·

Answer 10 · 2022-10-27T10:11:57Z

pedaaa answered · Oct 27, 2022 at 10:11 AM

Have done the Venus OS and MK3 Updates.

Is it also required to Update the Multi Firmware to accept the faster Gridmeter readings?

1666865460735.png (5.8 KiB)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

dirk-s commented · Oct 27, 2022 at 11:21 AM

No

1 ·

Answer 11 · 2022-10-27T18:16:59Z

pedaaa answered · Oct 27, 2022 at 06:16 PM

Done the Updates. I use an EM540 gridmeter.

The readings are now super fast, yes. But it dont feels like the control speed has really changed much?!

Maybe its still this 400W/s limit?!

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

dirk-s commented · Oct 28, 2022 at 01:46 AM

Yes, it's still around 400W/s. As fare as I know, it's a Grid rule. But I'm not totally sure.

0 ·

Answer 12 · 2022-10-30T19:44:52Z

mbosys answered · Oct 30, 2022 at 07:44 PM

Cheers mvader, for all your work on the updates!
Just tried this latest rev but finding the regulation of grid worse than before though and jumping around.

Have the EM24 meter with solar on phase 2, speed of updates had doubled, which is great!
but have noticed my Quattro 10K AC out Amps changing and not matching the KW, have included a video below.

Not sure if this is to do with the calculation in the background but seem quite unstable now. swings of over 200W each way, even when AC out is only moving 10's of watts.
Not sure if anything can be done? looks like the PID algo you use maybe a bit to sensitive now?

Thanks

Screen_Recording_20221030_183241_VRM.mp4

screen-recording-20221030-183241-vrm.mp4 (1.0 MiB)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:28 AM

noted! We'll look into that.

0 ·

Answer 13 · 2022-10-31T07:38:37Z

chrisu answered · Oct 31, 2022 at 07:38 AM

Still having lockups with the EM24 Ethernet - please fix this!

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

hpheuer commented · Nov 01, 2022 at 09:34 AM

Me too, unreproducable Ethernet-lockups since update to V2.92. Not every day, but after a couple days. System works fine, but Ethernet is dead. Needed to turn off-on the Multiplus.

Now I switched to an CAT7 cable, had CAT6 before, about 3 meters long. Please fix. Thanks!

0 ·

mvader (Victron Energy) ♦♦ hpheuer commented · Nov 04, 2022 at 08:24 AM

Yes, its incredibly frustrating and our hands are rather tied with regards to fixing that.

BUT.... I can say that we've recently (a few days ago) received a beta firmware from CG to test, and it survived our "extreme ethernet punishment" scripts and tests, where the old one would normally fail within a few hours. So, there is light on the horizon here.

Now all we need to do is await official release and then we'll make that available on https://professional.victronenergy.com as usual and I'll go through some threads here on community to announce it as well.

Do pls note that this off topic for this thread, since the issues are not related to Venus OS itself, and as such I ask you to not start a long discussion here. Thanks!

1 ·

Answer 14 · 2022-10-31T13:50:59Z

matthias-roetzer answered · Oct 31, 2022 at 01:50 PM

It is not clear to me if the MK3 update ist mandatory or optional when using meters (eg ET112, ET340) with Venus OS 3.00 ? Please clarify. Thank you, Matthias

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:25 AM

Hi Matthias, its optional. Doing it will result in better operating ESS, also with those meters. But not doing will just leave all as is; sort of.

0 ·

Answer 15 · 2022-10-31T16:54:47Z

phil-garver answered · Oct 31, 2022 at 04:54 PM

With this version I am running into an issue where the AC load, when on inverter, the AC load disappear and the status of the inverter will show as off. While the screenshot below has GUImods, this same issue happens in the VRM portal as well. I reverted to the pervious version and this issue went away. It will bounce back to proper status and then disappear on an ongoing basis.

1667234865805.png (60.9 KiB)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:28 AM

Hi, your screenshots shows the guimods; which is not Victron software.

We don't give any support on modded firmware, and I personally refuse to even start to think what could be the issue for such reports.

Venus OS by itself is already quite complex; and having to then consider what could be wrong in someone else his software too is just too much. It has "bitten" us a few times before, when trying to be nice and do look into it.

Note that this message is not at all ill intended. So, to get us to look into it, make sure its a totally clean installation, for which the only solution is to run a reset to factory default as explained in the manual.

Hope you understand!

3 ·

Answer 16 · 2022-11-01T08:50:10Z

corradopignato answered · Nov 01, 2022 at 08:50 AM

Is an updated MK3 still usable with Venus OS 2.92?

I have my whole home connected to out 1 of my multiplus. II

Is it safe to update mk3 in this scenario?

If I update, the temporary system outage will interrupt power on out 1? If so my internet connection will be interrupted. In this case, will the update process of the MK3 be complete without problems?

thx

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:35 AM

Hi @corrado.pignato@gmail.com good question. And yes, you can still roll back.

And its no issue that internet might briefly drop. no worries about that.

ps. you might want to consider to change your handle or username, to no longer be similar or equal to your email address. In order to reduce spam.

0 ·

Answer 17 · 2022-11-01T16:21:15Z

thomasw-1 answered · Nov 01, 2022 at 04:21 PM

Hi Matthijs,

can confirm properly working update cycle in combination with the ABB meter.
Btw. thanks a lot for having followed on my recommendation supporting ABB meters as default.
Also thanks to Izaak for the close collaboration.
Please consider to add a proper ID resolution in VRM yet !-)

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Dec 22, 2022 at 07:57 PM

Hi @ThomasW. , super late answer ofcourse ;o), but very welcome and thank you!

0 ·

Answer 18 · 2022-11-02T10:46:24Z

chrisu answered · Nov 02, 2022 at 10:46 AM

Hello,

it seems in Node Red, the update cycle is now faster when getting values from Victron Nodes. Before it was 5 seconds, now it seems it is around 1 second? (Important if you want to count power consumption). Can you confirm?

3

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:21 AM

Hi @chrisu , yes I can confirm; its this line from the change log

Fix issue sometimes causing certain values to update slower than necessary.

And it happened to some products or situations, and not to others. I don't know any further the details and think/hope that just knowing that its solved whatever it was is good enough. :)

0 ·

chrisu mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:58 AM

Background is, I make a virtual consumption counter. I calculate the Total AC Consumption during daytime by adding the AC Consumption L1/L2/L3 together and divide it with the update interval to get the total energy consumption in wh. For this, exact timing is needed. The 5sec before were very exact.

1 ·

pcurtis chrisu commented · Nov 13, 2022 at 04:44 PM

@chrisu I do much the same to get daily totals. Solution will be to add a delay node configured to limit rates.

0 ·

Answer 19 · 2022-11-04T07:57:41Z

chrisu answered · Nov 04, 2022 at 07:57 AM

It seems the Amp Display for l1/l2/l3 is not correct for the abb b23

screenshot-20221104-085552.png (227.0 KiB)

5

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Nov 04, 2022 at 08:37 AM

noted we'll check

0 ·

Izak (Victron Energy Staff) ♦♦ commented · Nov 04, 2022 at 11:14 AM

Hi @chrisu,

For the ABB meters the current values are always positive. The meter itself reports it that way, and probably for good reason too: With AC power current is technically never negative, only in- or out of phase. It is therefore normal that the current is always positive.

This is a little different from some of the other meters we support, some which do show negative current when the power is negative.

0 ·

chrisu Izak (Victron Energy Staff) ♦♦ commented · Nov 04, 2022 at 11:27 AM

Sure i knew that, but the current is wrong. 287w is not 3.4a at 230v

0 ·

Izak (Victron Energy Staff) ♦♦ chrisu commented · Nov 04, 2022 at 12:11 PM

Hi @chrisu , 287W could well be 3.4A if your power factor is only 0.4.

What you can do to verify, is on the meter itself, hold the OK button for about a second, when you let go the display will show "Instan" (for instantaneous values). Then short-press OK, and hit the down button. Look at the VA number. This should be equal to the volts multiplied by the amps. If you continue cycling you will also see the current, and the power factor. Check if the current is really significantly different from what the GX device reports. If it is, let us know, but it should not be.

0 ·

chrisu Izak (Victron Energy Staff) ♦♦ commented · Nov 04, 2022 at 01:05 PM

You are right

VA and W on the Meter is correct, but current is wrong.

Instead of readiing the modbus register for current it would be better then to calculate the current from volts and VA. Then youll have the negative current numbers also.

0 ·

Answer 20 · 2022-11-04T10:14:25Z

PeterM answered · Nov 04, 2022 at 10:14 AM

How far back can the MK3 firmware be installed in a Multiplus 1 ? Would like to get a new Multi 1 to parallel with my older one ( large processor - currently on v497).

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Dec 22, 2022 at 08:05 PM

Hi @Merle.Peter , the MK3 is in the GX device itself.

For paralleling old & new Multis, best consult your dealer to see if something is possible. Or ask in the main community forum.

0 ·

Answer 21 · 2022-11-05T14:55:23Z

markus-001 answered · Nov 05, 2022 at 02:55 PM

Remote console

Enable on LAN is defaulted to on even though it was turned off after restart.

Cerbo and Venus

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

mvader (Victron Energy) ♦♦ commented · Dec 22, 2022 at 08:07 PM

Hi @Markus_001 , thank you for the report. And sorry for my late reply. We'll test this.

0 ·

Answer 22 · 2022-11-06T06:51:15Z

fantail answered · Nov 06, 2022 at 06:51 AM

Had some issues with testing of this version. they have added some addition sw that polls the serial ports without respecting the soft lock flags when they are set -- this behavior causes corruption and data collisions.

both methods are being used - to hold exclusive control of port. - these a are soft flags so do not prevent others from trying to use the hardware ports directly.

result = ioctl(fd1, TIOCEXCL);

and

if ( flock(fd1, LOCK_EX | LOCK_NB) < 0 ) {

last works up to 2.87

serial port access tasks added since 2.87 need to learn manners!!!!!!!!!!!

Also like to see options added to block access to defined ports within serial starter task. ( full serial number added or simular )

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

jeroen ♦ commented · Dec 22, 2022 at 08:10 PM

see https://github.com/victronenergy/venus/wiki/howto-add-a-driver-to-Venus

0 ·

mvader (Victron Energy) ♦♦ commented · Dec 22, 2022 at 08:13 PM

Hi @Fantail , I think your best bet is to reserve the port using serial-starter.

Best documentation I have for that is here:

https://github.com/victronenergy/venus/wiki/howto-add-a-driver-to-Venus#3-installing-a-driver

And for any further discussion, please make a new question in the Modifications section - instead of continuing here. Thank you!

0 ·

Answer 23 · 2022-11-07T07:18:43Z

anieuwstadt answered · Nov 07, 2022 at 07:18 AM

1.) With the ABB B24, it looks like there is a problem with the register being read for the "Grid Total Energy to net". Grid Total Energy from net looks correct.

2.) Seen a significant improvement in control loop speed. Thank you.

1667804305235.png (49.4 KiB)

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

chrisu commented · Nov 08, 2022 at 01:43 PM

Interesting... I have the B23 and don't have the "energy meter" device in vrm.

0 ·

mvader (Victron Energy) ♦♦ chrisu commented · Dec 22, 2022 at 08:16 PM

Hi @anieuwstadt , could it be you have the "steel" version of the ABB meter?

We found some issues with that, and have since clarified the manual more, by saying that its not fully compatible.

"Note that the 'Steel' versions are not supported as they do not allow measurement of reverse energy, making it impossible to see sold energy. Charts and counters on VRM will not display correctly with a Steel meter. Make sure the meter you're purchasing is of the Silver (or better) designation and has Modbus RS485."

https://www.victronenergy.com/media/pg/Energy_Meter_ABB_B21_B23_and_B24/en/abb-b21,-b23-and-b24-energy-meter.html

0 ·

Answer 24 · 2022-11-08T07:39:55Z

CristiMV answered · Nov 08, 2022 at 07:39 AM

After installing the FW 3.00~4, the AC-In Fronius inverter is not showed anymore on the CerboGX start page and neither on the VRM dashboard. Still, the inverter appears in the device list - see pictures below. I've restarted the Cerbo, but no change. Any advice, other than rolling back to the previous version?

cerbogx.jpg (55.2 KiB)

cerbogx-menu.jpg (54.1 KiB)

vrm-device-list.jpg (48.8 KiB)

4

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

CristiMV commented · Nov 08, 2022 at 09:10 AM

I’ve rolled back to previous version and everything is back to normal.

0 ·

mvader (Victron Energy) ♦♦ CristiMV commented · Dec 22, 2022 at 08:30 PM

Hi @cristimv , today we released v3.00~14. Can I ask you to install that and see if the problem is stil lthere? If it is, please let me know by adding a comment there: https://community.victronenergy.com/questions/176323/venus-os-v30014-available-for-testing.html

thank you!

0 ·

iromeo commented · Nov 09, 2022 at 07:03 PM

Not related to this, but i saw you have both a symo and a primo. Do they work well on the same phase? (assuming the primo is allowed to feed).

Can I bother you a bit to understand how your setup is, please?

0 ·

Stefanie (Victron Energy Staff) ♦♦ iromeo commented · Nov 09, 2022 at 07:21 PM

Not related to this

So please open a new question. This is all about the latest beta version of Venus OS. Thank you.

0 ·

Answer 25 · 2022-11-11T07:19:19Z

anieuwstadt answered · Nov 11, 2022 at 07:19 AM

ABB B24 Energy export not reporting correctly. Could be related to previous post about B24 export energy register being incorrect.

System overview shows 3.0 kWh to grid and 48kWh from grid.

Whereas Energy meter shows substantial feed-in to the grid for the same period.

Cannot roll back to the prior version as this is a 24/7 production system with few system maintenance windows.

1668150635025.png (50.0 KiB)

1668150710913.png (43.5 KiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 26 · 2022-11-13T08:59:27Z

tomcat answered · Nov 13, 2022 at 08:59 AM

There is a strange behavior with the EM540 and Phase Sequence in VenusOS (v3.00~4)Wiring is double checked and pedaaa is reporting the same:

https://community.victronenergy.com/questions/143192/em540-grid-meter.html

Dont know if its related to VenusOS or EM540.

phasesequenz.jpg (38.5 KiB)

3

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

pedaaa commented · Nov 13, 2022 at 09:14 AM

i don´t think this is a Victron issue. As the same Phase sequence error is shown, if you connect the EM540 to the original Carlo Gavazzi UCS7 Software:

there is a possibility to "correct" this within UCS7 Software "virtually"

But i didn´t tried that, as it seem to be even more incorrect then ;)

0 ·

20220819-124455-resized.jpg (296.5 KiB)

virtu.jpg (426.8 KiB)

Show more comments

Answer 27 · 2022-11-19T08:37:36Z

majh answered · Nov 19, 2022 at 08:37 AM

I started running 3.0 - is the root filesystem read only now ? I think before it was read write and I was able to modify files ?

1

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Stefanie (Victron Energy Staff) ♦♦ commented · Nov 19, 2022 at 10:01 AM

It's been like that since Venus OS 2.80. See release notes here: https://community.victronenergy.com/questions/97155/venus-os-v28010-available-for-testing.html

1 ·

Answer 28 · 2022-11-19T10:02:32Z

Paul B answered · Nov 19, 2022 at 10:02 AM

Issue when using fw 3.00~7

Using a Multiplus II 48 5000 on fw 500 and the cerbo on fw 3.00~7 and the BMS is a 123smart BMS using there latest firmware v1.9 and connected to the cerbo via the 123smart USB data cable.

Main grid is connected. Grid Tie solar is operational and exporting to grid.

Error been seen is below.

*********************************

Under DVCC if I turn the new feature being Controlling BMS set to *** No BMS Control *** then I get a Low voltage warning and the Multiplus II flashes the low voltage warning light

Turning the 123smart BMS back on removes/resolves the warning issue

I would have expected that turning the BMS OFF would produce NO system errors including a low voltage warning when there is no low voltage and there is NO setting to even set that voltage level

the BMS parameters at the time are reading fine.

This warning is similar to a warning if the main battery has been disconnected or the fuse is blown when mains power is connected. (none of these issue had occured)

1668851495068.png (30.9 KiB)

1668851599318.png (30.5 KiB)

1668851710826.png (18.9 KiB)

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Answer 29 · 2022-11-20T13:23:57Z

chrisu answered · Nov 20, 2022 at 01:23 PM

Hi there,

I'm having a strange issue with the charging rate. Didn't noticed that before because we had hardly sun. But right now I noticed that not all pv power is pumped to the battery, it is limited at around 2000W/40A

Having a Multiplus-II 48/5000 and 2x Pylontech US3000C, it should go up to full ~75A when there is enough sun.

The BMS is setting the max. charging rate to 74A, in DVCC the maximum charging rate is set to 80A and should not limit it at all. To disable the Charging rate in DVCC completely makes no difference.
With 3.00~7, it is the same.

2

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

chrisu commented · Nov 21, 2022 at 09:15 AM

ok, switched back to 2.92 and it was also limited to ~40A.

I shut down the complete system and rebooted, it's now charging with full speed. Updated to 3.00~7 and it also works with full speed. Maybe the Update to MK3 with the 3.00 needs a reboot of the whole system?

cheers

0 ·

mvader (Victron Energy) ♦♦ chrisu commented · Dec 22, 2022 at 08:35 PM

Not sure about that, but good to know. Thank you for the report!

0 ·

Answer 30 · 2022-11-23T03:45:51Z

smart-home answered · Nov 23, 2022 at 03:45 AM

It doesn't look like /data/home/nodered/.node-red/settings-user.js is recognised on startup.....

Since v2.90 when these files were changed from previously using settings.js, I find my context storage settings are no longer recognised.
Possibly this hasn't been working since Feb 2022.

Has anyone found settings in settings-user.js to be effective?

3

2 |3000

Attachments: Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Dirk-Jan Faber (Victron Energy) ♦♦ commented · Nov 25, 2022 at 10:43 PM

I have it working without problems. It does need 'module.exports = {}' enclosed around the configuration. You may have missed that. E.g.:

module.exports = {
    contextStorage: {
        default: {
           module:"localfilesystem",
        }
    },
    editorTheme: {
        page: {
            title: "Victron",
        }
    }
}

2 ·

smart-home Dirk-Jan Faber (Victron Energy) ♦♦ commented · Nov 26, 2022 at 10:29 PM

Thanks @Dirk-Jan Faber and @pcurtis

Indeed, I had not enclosed my changes within “module.exports”.
Now edited, tested and working as designed….

0 ·

pcurtis commented · Nov 26, 2022 at 04:23 PM

@Smart-Home Confirm working for Context Storage. I also initially missed the need for wrapping with

module.exports = { 
.........
 }

I use

module.exports = {
   contextStorage: {
      default: "memoryOnly",
      memoryOnly: { module: 'memory' },
      file: { module: 'localfilesystem' }
    }
}

to have option of memory or file presented in, for example, Switch Nodes

1 ·

1669479430194.png (12.2 KiB)

question

Venus OS v3.00~4 available for testing

Related Resources

question details

Modifications Space

Node Red Space

question

Venus OS v3.00~4 available for testing

Related Resources

question details

Related Questions

Modifications Space

Node Red Space