This site is now in read-only archive mode. Please move all discussion, and create a new account at the new Victron Community site.
Hi
Can someone help point me in the right direction.
I am applying for a G99 connection in the UK and having some trouble providing an acceptable single line diagram.
I have attached how my setup should look but is there an easy way to turn this into a single line diagram that the DNO will accept.
Cheers
Mal
@thepilot I've hopefully got my G99 finally sorted Friday next week after a year of issues from my PV installer. Several comments I had in relation to my G99 schematic is firstly they are not interested in the DC side of the system. I was advised to have a AC schematic local to the incoming supply in my house should any operatives need to attend my property as they will need to know how to make the installation side if they had to work on the supply. Im yet to do this but in short the main info they need to know is where the main isolation points are to prevent electrical current going back down the incoming supply if they need to work on the system, any critical loads within the building. The distribution within the house they are not concerned with - light circuits, sockets, etc.
Thanks... my system will look close to that shown here
except with a MP2 48/5000 and my shunt will be closer to the battery.
so what you are saying is, I need to show where the battery and solar isolaters are, in the systom ?
For my G99 application, I used g59projects.co.uk who created a generic SLD for me which I promised I wouldn't share with anyone since it's part of their intellectual property. But I was quite surprised at just how simple the SLD actually was. It was really only the bare minimum to get through the application process and when it comes to commissioning time, you have the opportunity to submit a revised SLD to represent your actual installation. I did this and created my own SLD using an iPad app called "Single-line". It's an infuriating little app with quite a few bugs but I managed to create the attached SLD. Note that my SLD is much more detailed than the one that was sent with my application and there is a risk that adding that extra detail might increase the chances of an issue.
Note the clear delineation between DNO Network, Customer Network and New Installation and the various isolation switches and meters. As others have said above, they really don't care much beyond the AC side although I think they like to see the presence of a generic PV array and battery since these are key components of the ESS & PV system.
Note that I've still not heard back from my DNO since I submitted my commissioning documentation but I did chase them up a couple of weeks ago and they just said they had a backlog and that everything looks fine.
HTH
Thanks Craig
I could make something that looks like that using photoshop... as mine is almost the same as yours
I still don't know if I am doing the right form..
did you do the G99 Form A1-1 or the G99 Form A1-2 or ??
I have filled out the G99_Amd 8_A1.1.docx
just hoping it's right
Thanks again Craig, for sharing
I hope you don't mind... I just took yours and edited it in photoshop, to match my system
Here for anyone that wants to see, what I just submited, to NG (WPD)
fingers crossed, that they will be happy with it
Sorry to dig up an old thread but your setup is near exactly the same as mine (excluding some brand names changes). Just wanted to check if DNO had any comments on the above, if not I'll use that as my basis.
Great to hear!
I've been trying to read up on everything they require. Feels like such an overcomplicated process or at least how they describe it is...
Once you've submit G99 A-1, was that it given all the equipment is type tested? Or did you need to submit further forms after installation?
on ENA you can find the testing forms for the unit, stating what tests they done and it’s compliance to the grid.
link here https://www.ena-eng.org/gen-ttr/ just select find and put in victron and and then inverter in the other bit and it should pop up with the compliance forms i submitted them to with my application. the DNO did not require witnesses testimony from me and approved it once they done my fuse upgrade. Hope that helps
I remember you mentioning you had an electrician friend sign off your MCS, did they need to give any of their info for DNO application or did you just leave that as yourself. I've started filling in forms and just left installer details blank for now might just say quotes outstanding.
