question

solgato avatar image
solgato asked

BMV-712 Temp Sensor

Regarding the optional temp sensor for the 712 unit, will adding this option alter the way the charging works or is it just a display reading?

My batteries are mounted in the hulls of my Catamaran and I live in the tropics, so I could see the advantage of adding this feature if it is going to change the behavior of my Smart 75/15 chargers by providing them with info to help them properly charge my batteries based on temps.

Thx.

BMV Battery MonitorTemperature Sensor
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

2 Answers
Mark avatar image
Mark answered ·

Yes this will enhance the battery charge parameters.

As you already stated, if you purchase the additional temperature sensor for the BMV-712, then you can create a VE Smart Network where the voltage & temperature data from the BMV-712 is used to better charge your battery.

The BMV voltage will account for any voltage drop in your MPPT cables & the BMV temperature data will be used for accurate & real time charge voltage compensation (due to temperature).

Please also note that the inbuilt temperature sensor in the MPPT only takes a reading in the morning just before the MPPT wakes up. That same temperature is then used for charge voltage compensation for the rest of the day - so it's not ideal & you can achieve a much better charge by using the BMV data.

As you already have a BMV-712 there is no need to consider a Smart Battery Sense (unless you have already used the 2nd input for something else like mid-point measurement).

4 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

solgato avatar image solgato commented ·

Thanks for the confirmation Mark, that’s what I was hoping to hear.

I’ve learned not to assume things work they way I think they will!

I’ll defimtiely get one installed now that I understand it’s benefits.

0 Likes 0 ·
Mark avatar image Mark ♦♦ solgato commented ·

No problem.

I agree that it's always best to check/confirm rather than to assume.

FYI this is the related extract from the VE smart networking manual;

https://www.victronenergy.com/live/victronconnect:ve-smart-networking

0 Likes 0 ·
solgato avatar image solgato Mark ♦♦ commented ·

Thanks again Mark. Ordered and on the way!

Even though I live in the tropics where we rarely see much fluctuation in temps, lately I’m adopting an all bets are off philosophy when it comes to climate. It’s been cold (for Hawaii) so it’ll be nice to have more accurate temp readings, especially if without the optional sensor the charge behavior is based only on a one time wake up measurement as you say. There’s a big difference between early morning conditions when on trailer in my driveway versus out on the water all day in the sun.

0 Likes 0 ·
Mark avatar image Mark ♦♦ solgato commented ·

Good to hear & your welcome!

FYI this is the extract from the Victron Connect MPPT manual regarding charge voltage compensation due to temperature;

0 Likes 0 ·
1553574027163.png (69.6 KiB)
Paul B avatar image
Paul B answered ·

if you purchase the victron smart sensor (bluetooth) then this would connect to the smart mppt and the bmx712 and yes the smartsolar mppt unit would adjust for temp and for volt drop as well

4 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

solgato avatar image solgato commented ·

Thanks, but I was asking about the optional temp sensor that can be wired into the second terminal of the shunt that comes with the BMV-712.

Since the 712 is already networked with my two Bluetooth MPPT 75/15’s it is transmitting voltage readings to my chargers, and I assume if I add the optional temp sensor it will send that info to them as well so that they can adjust their charge cycles based on battery temp instead of the temp measured by the chargers which are housed in a separate area, but I just wanted to make sure first since it’s possible it’s just a feature for monitoring that has no affect on the chargers behavior.

I assume if I install a sensor, the VictronConnect App will report that the BMV-712 is transmitting both voltage and temp and that my two 75/15’s are receiving when networked.

0 Likes 0 ·
Show more comments

Related Resources