question

liahskoolie avatar image
liahskoolie asked

Inverter loses charge every night. SOC reads 100%, but the inverter only turns on when the sun comes out.

img-0340.pngOur inverter doesn't seem to hold a charge anymore. We've only had this system for a couple of months. Everything was working perfectly. Out of nowhere we began to lose power in our RV in the middle of every night despite the SOC being very high and us using little electrical appliances during the night. The app shows the inverter is set to "off", despite trying to turn it on. Once the sun begins to rise, the app shows the inverter is still "off" while it is charging back up, and is usually at a super low voltage around 4-8V. After a few hours, it's up to around 13V, but then doesn't get much higher than that.


We have 3 lithium batteries connected that are fully charged. We see the inverter dies at night, and the app shows the low battery warning, yet the SOC is still very high (usually above 80%).

We believe the SOC trickles down to 80% because our lights are hardwired into the batteries.
img-0342.pngWe haven't had a problem for months up until now. We think it may have had to do with a recent software update. Also, we bought a space heater and used it in our outlets for a couple of days. We made sure our batteries didn't go below 70% while using it, just wanted to heat up the RV in the mornings. Sometimes, when using the heater, the power would cut out and then turn back on.


img-0341.pngWe've tried resetting everything to default, checking for updates, restarting the system - nothing works. Any help would be greatly appreciated.

Phoenix InverterSOCinverter current drawHot Water Diversion
img-0341.png (337.4 KiB)
img-0340.png (274.6 KiB)
img-0342.png (352.6 KiB)
2 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

3 Answers
Paul B avatar image
Paul B answered ·

Please only use the SOC in conjunction with checking battery voltage at the time of failure. also please check the below video as it may help you understand how the SOC works

Suspect you have a flat battery issue. yes it may say 100% SOC this maybe very misleading at times VOLTAGE IS KING OF THE ROAD always compare to voltage and check the individual cell voltages if you have lithium

https://www.youtube.com/watch?v=mEN15Z_S4kE


2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Alexandra avatar image
Alexandra answered ·

@liahskoolie

You have set on your shunt battery starts synchronised. So every time your system shuts down and restarts it is assuming the battery is full. So first step is to switch that off, it is giving you false soc.

Fully charge the batteries and you should be golden. Your batteries are shutting themselves down to protect themselves.

2 comments
2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Alexandra avatar image
Alexandra answered ·

@liahskoolie

A few other small changes (settings are for a bmv 700, bit the principles are the same) recommended by battleborn website.

Like you bank capacity is not 300ah but 3x99ah.

All loads should be connected to the load side of the shunt nothing should be directly connected to the battery, otherwise it also will not be able to calculate soc accurately.

Check your quick install manual.

2 |3000

Up to 8 attachments (including images) can be used with a maximum of 190.8 MiB each and 286.6 MiB total.

Related Resources

Additional resources still need to be added for this topic

Phoenix Inverter product page

Phoenix Inverter Smart product page